Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > Fuel Pump Control Circuit

for Preparation Click here


DESCRIPTION

The FUEL PUMP relay switches the fuel pump speed according to the engine conditions. The fuel pump operates when the ECM receives the starter-operating signal (STA) and crankshaft-rotating signal (NE).
The FUEL PUMP relay is turned ON while the engine is idling or operating at low load. This causes current to flow through the fuel pump resistor to the fuel pump. The fuel pump then operates at low speed.
The FUEL PUMP relay is turned OFF while the engine is cranking or operating at high load. The fuel pump then operates at normal speed.

A172777E01


WIRING DIAGRAM


A172702E02


A172703E02


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE C/OPN RELAY)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch on (IG), and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check the relay operation while operating it using the tester.

    Standard:
    Operating noise can be heard from the relay.



NG
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK


2.INSPECT TERMINAL VOLTAGE (FUEL PMP RELAY TERMINAL)


    A168245E02
  1. Remove the FUEL PMP relay from the engine room relay block.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    FUEL PMP relay terminal 2 - Body ground
    Ignition switch on (IG)
    9 to 14 V
    FUEL PMP relay terminal 3 - Body ground
    Ignition switch on (IG)
    9 to 14 V

  1. Reinstall the FUEL PMP relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL PMP RELAY - C/OPN RELAY)
OK


3.INSPECT RELAY (FUEL PMP RELAY)


    A137690
  1. Remove the FUEL PMP relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    When no battery voltage is applied terminals 1 and 2
    Below 1 Ω
    3 - 5
    When no battery voltage is applied terminals 1 and 2
    10 kΩ or higher
    3 - 4
    When battery voltage is applied terminals 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage is applied terminals 1 and 2
    Below 1 Ω

  1. Reinstall the FUEL PMP relay.



NG
REPLACE RELAY (FUEL PMP RELAY)
OK


4.INSPECT FUEL PUMP RESISTOR


    A174006E01
  1. Disconnect the fuel pump resistor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    0.30 to 0.34 Ω

  1. Reconnect the fuel pump resistor connector.



NG
REPLACE FUEL PUMP RESISTOR (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PMP RELAY)


    A172730E02
  1. Check the wire harness between the FUEL PMP relay and fuel pump.

    1. Remove the fuel pump relay from the engine room relay block.

    2. Disconnect the fuel pump connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      FUEL PMP relay terminal 4 - O9-4
      Always
      Below 1 Ω
      FUEL PMP relay terminal 4 or O9-4 - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (FUEL PUMP RELAY - FUEL PUMP RESISTOR)


    A172721E01
  1. Disconnect the fuel pump resistor connector.

  1. Remove the fuel pump relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    FUEL PMP relay terminal (5) - A35-1
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    FUEL PMP relay terminal (5) or A35-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the fuel pump resistor connector.

  1. Reinstall the fuel pump relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (FUEL PUMP RESISTOR - FUEL PUMP)


    A137393E05
  1. Disconnect the fuel pump resistor connector.

  1. Disconnect the fuel pump connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    A35-2 - O9-4
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    A35-2 or O9-4 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the fuel pump resistor connector.

  1. Reconnect the fuel pump connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT FUEL PUMP


    A172728E02
  1. Inspect the fuel pump.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connections
      Condition
      Specified Condition
      4 - 5
      20°C (68°F)
      0.2 to 0.3 Ω

    2. Apply battery voltage to both terminals 4(+) and 5(-). Check that the pump operates.

      NOTICE:
      1. These tests must be done quickly (within 10 seconds) to prevent the coil from burning out.
      2. Keep the fuel pump as far away from the battery as possible.
      3. Always turn ON and OFF the voltage on the battery side, not on the fuel pump side.



NG
REPLACE FUEL PUMP ASSEMBLY (Click here)
OK

CHECK AND REPLACE FUEL FILTER 

9.CHECK ECM POWER SOURCE CIRCUIT

HINT:
(Click here).



NG
REPAIR OR REPLACE ECM POWER SOURCE CIRCUIT
OK


10.INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (C/OPN RELAY)
  1. Inspect the C/OPN relay (Click here).



NG
REPLACE CIRCUIT OPENING RELAY (Click here)
OK


11.INSPECT ECM (FC VOLTAGE)


    A168199E29
  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D35-10 (FC) - B3-1 (E1)
    Ignition switch on (IG)
    9 to 14 V



NG
Go to step 12
OK

REPLACE ECM (Click here)  

12.CHECK HARNESS AND CONNECTOR (ECM - C/OPN RELAY)


    A172720E02
  1. Disconnect the ECM connector.

  1. Remove the engine room junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    D35-10 (FC) - 2D-12 (C/OPN relay terminal)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    D35-10 (FC) or 2D-12 (C/OPN relay terminal) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reinstall the engine room junction block.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - C/OPN RELAY)
OK

REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLY (Click here)