Home › BODY ELECTRICAL › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > All Doors LOCK/UNLOCK Functions do not Operate Via Master Switch, Driver Side Door Key Cylinder

for Preparation Click here


DESCRIPTION

The main body ECU (instrument panel junction block) receives switch signals from the power window master switch and driver side door key cylinder, and activates the door lock motor on each door according to these signals.

WIRING DIAGRAM


B171370E01


INSPECTION PROCEDURE

1.INSPECT FUSE (DOOR1)
  1. Remove the DOOR1 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    DOOR1 fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE (DOOR1)
OK


2.CHECK DOOR LOCK OPERATION

Result:

Result
Proceed to
Doors cannot be locked through driver side door key cylinder.
A
Doors cannot be locked through master switch.
B



A
Go to step 6
B


3.READ VALUE USING TECHSTREAM
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus:
    Body Electrical / Main Body / Data List.

  1. Select Door Lock SW-Lock or Door Lock SW-Unlock in the Data List and read the tester display.

    Main Body (Main Body ECU): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Lock SW-Lock
    Door manual lock switch signal/ON or OFF
    ON: Door control switch on power window regulator master switch is pushed to LOCK
    OFF: Door control switch on power window regulator master switch is not pushed
    -
    Door Lock SW-Unlock
    Door manual unlock switch signal/ON or OFF
    ON: Door control switch on power window regulator master switch is pushed to UNLOCK
    OFF: Door control switch on power window regulator master switch is not pushed
    -

    OK:
    On the tester screen, each item changes between ON and OFF according to the chart above.



NG
Go to step 4
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK) 

4.INSPECT POWER WINDOW MASTER SWITCH
  1. Remove the power window master switch (Click here).



    B164359E13
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Locked
    Below 1 Ω
    1 - 2
    1 - 9
    OFF (Free)
    10 kΩ or higher
    1 - 9
    Unlocked
    Below 1 Ω



NG
REPLACE POWER WINDOW MASTER SWITCH (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (POWER WINDOW MASTER SWITCH CIRCUIT)


    B171371E01
  1. Disconnect the instrument panel junction block connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    M1-2 (L) - 1K-15
    Always
    Below 1 Ω
    M1-9 (UL) - 1K-12
    Always
    Below 1 Ω
    M1-1 (E) - Body ground
    Always
    Below 1 Ω
    M1-2 (L) - Body ground
    Always
    10 kΩ or higher
    M1-9 (UL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK) 

6.READ VALUE USING TECHSTREAM (DOOR KEY LINKED LOCK AND UNLOCK SWITCH)
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus:
    Body Electrical / Main Body / Data List.

  1. Select Door Key SW-Lock or Door Key SW-Unlock in the Data List and read the tester display.

    Main Body (Main Body ECU): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Key SW-Lock
    Door key linked lock switch signal/ON or OFF
    ON: Driver side door key cylinder is turned to LOCK
    OFF: Driver side door key cylinder is not turned
    -
    Door Key SW-Unlock
    Door key linked unlock switch signal/ON or OFF
    ON: Driver side door key cylinder is turned to UNLOCK
    OFF: Driver side door key cylinder is not turned
    -

    OK:
    On the tester screen, each item changes between ON and OFF according to the chart above.



NG
Go to step 7
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK) 

7.INSPECT FRONT DOOR LOCK ASSEMBLY (FOR DRIVER SIDE)


    B164389E06
  1. Remove the front door lock assembly LH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    7 - 9
    ON (Door lock set to LOCK)
    Below 1 Ω
    7 - 9
    7 - 10
    OFF (Free)
    10 kΩ or higher
    7 - 10
    ON (Door lock set to UNLOCK)
    Below 1 Ω



NG
REPLACE FRONT DOOR LOCK ASSEMBLY (FOR DRIVER SIDE) (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (DOOR KEY LINKED LOCK UNLOCK SWITCH CIRCUIT)


  1. Disconnect the main body ECU (instrument panel junction block) and instrument panel junction block connectors.


    B171372E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    H6-9 (L) - 1K-16
    Always
    Below 1 Ω
    H6-10 (UL) - D8-10 (UL3)
    Always
    Below 1 Ω
    H6-7 (E) - Body ground
    Always
    Below 1 Ω
    H6-9 (L) - Body ground
    Always
    10 kΩ or higher
    H6-10 (UL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)