STEERING PAD > DISPOSAL |
| 1. PRECAUTION |
| 2. DISPOSE OF STEERING PAD (WHEN INSTALLED IN VEHICLE) |
![]() |
Check the function of SST.
![]() |
Connect SST to the battery.
Connect the red clip of SST to the battery positive (+) terminal and the black clip of SST to the negative (-) terminal.
![]() |
Check the function of SST.
Press the SST activation switch and check that the LED of the SST activation switch comes on.
Disconnect SST from the battery.
Refer to PRECAUTION (Click here).
![]() |
Remove the steering column cover (lower).
While turning the steering wheel assembly to the right and left, remove the 2 screws and steering column cover (lower).
Disconnect the cable from the negative battery terminal.
Install SST.
Disconnect the airbag connector (yellow colored one) from the spiral cable.
![]() |
Connect the SST connector to the airbag connector of the spiral cable.
![]() |
Move SST at least 10 m (33 ft.) away from the vehicle front side window.
Maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.
Connect the red clip of SST to the battery positive (+) terminal and the black clip of SST to the negative (-) terminal.
Deploy the airbag.
Check that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.
Press the SST activation switch and deploy the airbag.
| 3. DISPOSE OF STEERING PAD (WHEN NOT INSTALLED IN VEHICLE) |
![]() |
Check the function of SST.
![]() |
Connect SST to the battery.
Connect the red clip of SST to the battery positive (+) terminal and the black clip of SST to the negative (-) terminal.
![]() |
Check the function of SST.
Press the SST activation switch and check that the LED of the SST activation switch comes on.
Disconnect SST from the battery.
Remove the steering pad (Click here).
![]() |
Using braided wire, tie down the steering pad to an unneeded wheel.
![]() |
Install the 2 bolts with washers into the 2 bolt holes on the steering pad.
![]() |
After connecting the following SST to each other, connect them to the steering pad.
![]() |
Wind 3 wires at least 2 times each around each of the bolts installed on the left and right sides of the steering pad.
![]() |
Face the airbag deployment side of the steering pad upward on top of an unneeded tire and wheel set. Separately tie the left and right sides of the steering pad to the wheel through the hub nut holes. Position the SST connector so that it hangs downward through the hub hole of the wheel.
![]() |
Install SST.
Connect the SST connector.
![]() |
Move SST at least 10 m (33 ft.) away from the airbag tied down to the wheel.
![]() |
Cover the steering pad (using a cardboard box).
Cover the steering pad with the cardboard box.
Place weights on the cardboard box in 4 places totalling at least 190 N (19 kg, 43 lb).
Cover the steering pad (using tires).
![]() |
Place at least 3 tires without wheels onto wheel and tire which the steering pad is tied to.
Place the wheel and tire on top of them.
![]() |
Tie the tires together with the 2 wires.
Deploy the airbag.
![]() |
Connect the red clip of SST to the battery positive (+) terminal and the black clip of SST to the negative (-) terminal.
Check that no one is within a 10 m (33 ft.) radius of the wheel which the steering pad is tied to.
Press the SST activation switch and deploy the airbag.
![]() |
Dispose of the steering pad.
Remove the steering pad from the wheel.
Place the steering pad in a plastic bag, tie it tightly and dispose of it according to local regulations.