Home › BODY › SLIDING ROOF › SLIDING ROOF SYSTEM

SLIDING ROOF SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)

B050671E38

  1. Disconnect the Q12 ECU connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Q12-1 (B) - Q12-2 (E)
    B - W-B
    +B power supply
    Always
    10 to 14 V
    Q12-5 (IG) - Q12-2 (E)
    Y - W-B
    Ignition switch power supply
    Ignition switch off
    Below 1 V
    Q12-5 (IG) - Q12-2 (E)
    Y - W-B
    Ignition switch power supply
    Ignition switch on (IG)
    10 to 14 V
    Q12-7 (OPN) - Q12-2 (E)
    V - W-B
    Sliding roof motor open
    OPEN switch OFF
    10 kΩ or higher
    Q12-7 (OPN) - Q12-2 (E)
    V - W-B
    Sliding roof motor open
    OPEN switch ON
    Below 1 Ω
    Q12-9 (CLS) - Q12-2 (E)
    W - W-B
    Sliding roof motor closed
    CLOSE switch OFF
    10 kΩ or higher
    Q12-9 (CLS) - Q12-2 (E)
    W - W-B
    Sliding roof motor closed
    CLOSE switch ON
    Below 1 Ω
    Q12-10 (UP) - Q12-2 (E)
    BR - W-B
    Sliding roof motor up
    UP switch OFF
    10 kΩ or higher
    Q12-10 (UP) - Q12-2 (E)
    BR- W-B
    Sliding roof motor up
    UP switch ON
    Below 1 Ω
    Q12-8 (DWN) - Q12-2 (E)
    P - W-B
    Sliding roof motor down
    DOWN switch OFF
    10 kΩ or higher
    Q12-8 (DWN) - Q12-2 (E)
    P - W-B
    Sliding roof motor down
    DOWN switch ON
    Below 1 Ω
    Q12-2 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the Q12 ECU connector.

  4. Measure the voltage according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Q12-7 (OPN) - Q12-2 (E)
    V - W-B
    Sliding roof motor open
    Ignition switch on (IG), sliding roof closed, OPEN switch OFF
    Below 1 V
    Q12-7 (OPN) - Q12-2 (E)
    V - W-B
    Sliding roof motor open
    Ignition switch on (IG), sliding roof closed, OPEN switch ON
    10 to 14 V
    Q12-9 (CLS) - Q12-2 (E)
    W - W-B
    Sliding roof motor closed
    Ignition switch on (IG), sliding roof open, CLOSE switch OFF
    Below 1 V
    Q12-9 (CLS) - Q12-2 (E)
    W - W-B
    Sliding roof motor closed
    Ignition switch on (IG), sliding roof open, CLOSE switch ON
    10 to 14 V
    Q12-10 (UP) - Q12-2 (E)
    BR - W-B
    Sliding roof motor up
    Ignition switch on (IG), sliding roof tilted downward, UP switch OFF
    Below 1 V
    Q12-10 (UP) - Q12-2 (E)
    BR - W-B
    Sliding roof motor up
    Ignition switch on (IG), sliding roof tilted downward, UP switch ON
    10 to 14 V
    Q12-8 (DWN) - Q12-2 (E)
    P - W-B
    Sliding roof motor down
    Ignition switch on (IG), sliding roof tilted upward, DOWN switch OFF
    Below 1 V
    Q12-8 (DWN) - Q12-2 (E)
    P - W-B
    Sliding roof motor down
    Ignition switch on (IG), sliding roof tilted upward, DOWN switch ON
    10 to 14 V
    If the result is not as specified, the ECU may have a malfunction.