FRONT SEAT ASSEMBLY (for Manual Seat) > DISASSEMBLY |
| 1. REMOVE VERTICAL SEAT ADJUSTER KNOB |
![]() |
Using a screwdriver wrapped with protective tape, remove the snap ring as shown in the illustration.
Remove the vertical seat adjuster knob.
| 2. REMOVE RECLINING ADJUSTER RELEASE HANDLE |
![]() |
Using a screwdriver wrapped with protective tape, disengage the claw and remove the reclining adjuster release handle.
| 3. REMOVE VERTICAL ADJUSTER COVER |
![]() |
Using a screwdriver wrapped with protective tape, disengage the 2 claws and remove the vertical adjuster cover.
| 4. REMOVE VERTICAL ADJUSTING HANDLE |
![]() |
Remove the 2 screws and the vertical adjusting handle.
| 5. REMOVE FRONT SEAT CUSHION SHIELD |
![]() |
Disengage the hooks.
![]() |
Remove the 3 screws.
Disengage the claw.
Disengage the 2 guides and remove the front seat cushion shield.
| 6. REMOVE FRONT SEAT INNER BELT ASSEMBLY |
Disconnect each connector and clamp.
![]() |
Remove the nut and the front seat inner belt assembly.
| 7. REMOVE FRONT SEAT CUSHION INNER SHIELD |
![]() |
Remove the screw.
Disengage the claw.
![]() |
Separate the guide and remove the front seat cushion inner shield as shown in the illustration.
| 8. REMOVE FRONT SEAT CUSHION COVER WITH PAD |
![]() |
Disengage the clamp.
for Front Passenger Side:
w/ Seat Heater System:
Disconnect the seat heater connector.
Using a clip remover, remove the 2 clips.

Disengage the hooks and remove the front seat cushion cover with pad as shown in the illustration.
| 9. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER |
![]() |
Remove the 6 hog rings.
![]() |
Remove the 11 hog rings and the separate type front seat cushion cover.
| 10. REMOVE FRONT SEATBACK COVER WITH PAD |
![]() |
Remove the 3 hog rings.
![]() |
Remove the 5 hog rings.
![]() |
Disengage the 2 hooks.
![]() |
Turn back the separate type front seatback cover to remove the nut, and separate the bracket of the separate type front seatback cover.
![]() |
Disengage the 4 claws and remove the 2 front seat headrest supports.
Remove the separate type front seatback cover with pad from the front seat frame assembly with adjuster.
| 11. REMOVE SEPARATE TYPE FRONT SEATBACK COVER |
![]() |
Remove the 7 hog rings and the separate type front seatback cover.
| 12. REMOVE ACTIVE HEADREST UPPER UNIT |
![]() |
Remove the nut and disconnect the cable from the active headrest upper unit as shown in the illustration.
Remove the 4 nuts and the active headrest upper unit.
| 13. REMOVE ACTIVE HEADREST LOWER UNIT |
![]() |
Remove the 4 nuts and the active headrest lower unit.
| 14. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Remove the screw.
Disengage the clamp.
Disengage the guide and remove the reclining adjuster inside cover LH.
| 15. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Remove the screw.
Disengage the claw and remove the reclining adjuster inside cover LH.
| 16. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
![]() |
Remove the screw.
Disengage the guide and remove the reclining adjuster inside cover RH.
| 17. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
![]() |
Remove the screw.
Disengage the claw and remove the reclining adjuster inside cover RH.
| 18. REMOVE FRONT SEAT LOWER CUSHION SHIELD LH |
![]() |
Remove the screw.
Disengage the claw and remove the front seat lower cushion shield LH as shown in the illustration.
| 19. REMOVE FRONT SEAT LOWER CUSHION SHIELD RH |
![]() |
Remove the screw.
Disengage the claw and the guide, and remove the front seat lower cushion shield RH as shown in the illustration.
| 20. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY (for Front Passenger Side) |
![]() |
w/ Seat Heater System:
Disengage the 2 clamps and remove the seat heater control sub-assembly.
| 21. REMOVE SEAT POSITION SENSOR |
![]() |
Disconnect the connector.
Using a "TORX" socket wrench (T30), remove the "TORX" screw and seat position sensor with the seat slide position sensor protector.
![]() |
Remove the seat position sensor from the seat slide position sensor protector as shown in the illustration.
| 22. REMOVE OCCUPANT CLASSIFICATION ECU (for Front Passenger Side) |
![]() |
Disconnect the 2 connectors from the occupant classification ECU.
Disengage the claw and remove the occupant classification ECU.
| 23. REMOVE FRONT SEAT WIRE RH (for Front Passenger Side) |
Disengage the each clamps and remove the front seat wire RH.