Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) > Air Conditioning Compressor Magnetic Clutch Circuit

for Preparation Click here


DESCRIPTION

When the A/C amplifier is turned on, a magnetic clutch ON signal is sent from the MGC terminal of the A/C amplifier. Then, the MGC relay turns on to operate the magnetic clutch.

WIRING DIAGRAM


E154312E03


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch on (IG) and turn Techstream main switch on.

  1. Turn the A/C switch on and off.

  1. Select the item below in the Data List, and read the display on Techstream.

    Data List / Engine: 
    Tester Display
    Measure Item/Range
    Normal Condition
    Diagnostic Note
    A/C Signal
    (A/C Signal)
    A/C signal / ON or OFF
    ON: A/C ON
    OFF: A/C OFF
    -

    OK:
    The display is as specified in the normal condition column.



NG
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK


2.INSPECT FUSE (A/C NO. 2)
  1. Remove the A/C NO. 2 fuse from the instrument panel junction block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A/C NO. 2
    Always
    Below 1 Ω



NG
REPLACE FUSE (A/C NO. 2)
OK


3.INSPECT MAGNET-CLUTCH RELAY (MGC)


    B060778E04
  1. Remove the MGC relay from the engine room relay block and junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE MAGNET-CLUTCH RELAY (MG CLT)
OK


4.CHECK HARNESS AND CONNECTOR (A/C AMPLIFIER - BATTERY)


    E143742E76
  1. Disconnect the connector from the air conditioning amplifier.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D37-20 (MGC) - Body ground
    Ignition switch off
    Below 1 V
    D37-20 (MGC) - Body ground
    Ignition switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT AIR CONDITIONING AMPLIFIER


    E124471E39
  1. Reconnect the connector to the air conditioning amplifier.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D37-20 (MGC) - Body ground
    Ignition switch on (IG)
    Air conditioning switch: OFF
    11 to 14 V
    D37-20 (MGC) - Body ground
    Ignition switch on (IG)
    Air conditioning switch: ON
    Below 1 V



NG
REPLACE AIR CONDITIONING AMPLIFIER (Click here)
OK


6.INSPECT A/C COMPRESSOR


    E152688E05
  1. Disconnect the connector from the air conditioning compressor.

  1. Measure the resistance of the connector.

  1. When connector terminal 1 (MG+) is connected to the positive (+) battery terminal, and the body ground is connected to the negative (-) battery terminal, check that the following occurs: 1) the magnetic clutch's operating sound is emitted, and 2) the magnetic clutch's hub and rotor lock.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B45-1 (MG+) - Body ground
    Always
    Below 1 Ω



NG
REPLACE AIR CONDITIONING COMPRESSOR
OK


7.CHECK HARNESS AND CONNECTOR (ENGINE ROOM R/B AND J/B - BATTERY)


    E155266E02
  1. Remove the MGC relay from the engine room relay block and junction block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    Relay block MGC relay terminal 5 - Body ground
    Ignition switch on (IG)
    11 to 14 V
    Relay block MGC relay terminal 1 - Body ground
    Ignition switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM R/B AND J/B - BATTERY)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM R/B AND J/B - A/C COMPRESSOR)