AIRBAG SYSTEM > SYSTEM DESCRIPTION |
| GENERAL |
FRONTAL COLLISION
The driver airbag, front passenger airbag and driver side knee airbag are designed to supplement seat belts in the event of a front collision in order to help reduce shock to the head and chest of the driver and front passenger and knee of the driver.
Frontal collisions are detected by the center airbag sensor and two front airbag sensors. The driver airbag, front passenger airbag, driver side knee airbag and the seat belt pretensioners then operate simultaneously.
SIDE COLLISION
The front seat side airbag and curtain shield airbag are designed to help reduce shock to the driver, front passenger and rear outer passengers in the event of a side collision.
Side collisions are detected by the side airbag sensor installed in the bottom of the center pillar and the rear airbag sensor installed in the bottom of the rear pillar.
Front side collisions are detected by the side airbag sensor, causing the front seat side airbag and curtain shield airbag to deploy simultaneously. Rear side collisions are detected by the rear airbag sensor to deploy only the curtain shield airbag.
| CONSTRUCTION AND OPERATION |
FRONT AIRBAG SENSOR
The front airbag sensors are installed on the right and left radiator supports respectively.
The front airbag sensor uses an electrical type deceleration sensor.
The deceleration sensor is built into the front airbag sensor, and the distortion that is created in the sensor is converted into an electric signal based on the vehicle deceleration rate during a frontal collision. Accordingly, the extent of the initial collision can be detected in detail.
SIDE AIRBAG SENSOR
The side airbag sensors are installed on the bottom of the right and left center pillars respectively.
The side airbag sensor uses an electrical type deceleration sensor.
The deceleration sensor is built into the side airbag sensor, and the distortion that is created in the sensor is converted into an electric signal based on the vehicle deceleration rate during a front side collision. Accordingly, the extent of the initial collision can be detected in detail.
REAR AIRBAG SENSOR
The rear airbag sensors are installed on the right and left rear pillars respectively.
The rear airbag sensor uses an electrical type deceleration sensor.
The deceleration sensor is built into the rear airbag sensor, and the distortion that is created in the sensor is converted into an electric signal based on the vehicle deceleration rate during a rear side collision. Accordingly, the extent of the initial collision can be detected in detail.
CENTER AIRBAG SENSOR ASSEMBLY
General
Deceleration sensor and ignition control circuit
Safing sensor
The safing sensor is built into the center airbag sensor assembly. During a frontal, front side or rear side collision, the sensor turns on and outputs an ON signal to the center airbag sensor assembly if a deceleration rate sent to the safing sensor is greater than the specified value.
Backup power source
The backup power source consists of a power supply capacitor and a DC-DC converter. When the power system does not function during a collision, the power supply capacitor discharges and supplies electric power to the system. The DC-DC converter operates as a boosting transformer when the battery voltage falls below a predetermined level.
Diagnostic circuit
This circuit constantly diagnoses system malfunctions. When a malfunction is detected, it turns on the SRS warning light on the combination meter assembly to inform the driver.
Memory circuit
When a malfunction is detected in the diagnostic circuit, it is coded and stored in the memory circuit.
SRS WARNING LIGHT
The SRS warning light is located on the combination meter assembly. It comes on to inform the driver of system trouble when a malfunction is detected in self-diagnosis of the center airbag sensor assembly. Under normal operating conditions, when the ignition switch is turned on (IG), it comes on for approximately 6 seconds and then goes off.
| DEPLOYMENT CONDITION |
The center airbag sensor assembly determines whether ignition is necessary based on signals from the deceleration sensor and the front airbag sensor (*1). If the safing sensor turns on simultaneously, current flows to the squibs to deploy the SRS as shown in the illustration below.

The center airbag sensor assembly determines whether ignition is necessary based on signals from the side airbag sensor. If the safing sensor turns on simultaneously, current flows to the squib to deploy the SRS as shown in the illustration below.

The center airbag sensor assembly determines whether ignition is necessary based on signals from the rear airbag sensor (*1). If the safing sensor turns on simultaneously, current flows to the squib to deploy the SRS as shown in the illustration below.

The vehicle is equipped with the function to activate the SRS in case of vehicle rollover. A circuit to detect vehicle rollover is built into the center airbag sensor assembly. When the conditions for vehicle rollover are met, the SRS is activated as shown in the illustration below.
