Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1810/53    Short in Driver Side Squib 2nd Step Circuit

DTC    B1811/53    Open in Driver Side Squib 2nd Step Circuit

DTC    B1812/53    Short to GND in Driver Side Squib 2nd Step Circuit

DTC    B1813/53    Short to B+ in Driver Side Squib 2nd Step Circuit

for Preparation Click here


DESCRIPTION

  1. The driver side squib 2nd step circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad.
  2. The circuit instructs the SRS to deploy when deployment conditions are met.
  3. These DTCs are recorded when a malfunction is detected in the driver side squib 2nd step circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1810/53
  1. The center airbag sensor assembly receives a line short circuit signal 5 times in the driver side squib 2nd step circuit during primary check.
  2. Driver side squib 2nd step malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib 2nd step)
  4. Center airbag sensor assembly
B1811/53
  1. The center airbag sensor assembly receives an open circuit signal in the driver side squib 2nd step circuit for 2 seconds.
  2. Driver side squib 2nd step malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib 2nd step)
  4. Center airbag sensor assembly
B1812/53
  1. The center airbag sensor assembly receives a short circuit to ground signal in the driver side squib 2nd step circuit for 0.5 seconds.
  2. Driver side squib 2nd step malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib 2nd step)
  4. Center airbag sensor assembly
B1813/53
  1. The center airbag sensor assembly receives a short circuit to B+ signal in the driver side squib 2nd step circuit for 0.5 seconds.
  2. Driver side squib 2nd step malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib 2nd step)
  4. Center airbag sensor assembly

WIRING DIAGRAM


C145466E28


INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting the "check mode" (signal check) with Techstream (Click here).
  2. After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).

1.CHECK CONNECTORS


    C167973E02
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the steering pad, spiral cable and center airbag sensor assembly.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the steering pad, spiral cable and center airbag sensor assembly.

  1. Check that the connectors of the terminals are not damaged.

    OK:
    The terminals are not deformed or damaged.

  1. Check that the spiral cable connector (on the steering pad side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


2.CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP)


    C173751E01
  1. Connect the instrument panel wire to the center airbag sensor assembly and spiral cable.

  1. Connect SST (resistance 2.1 Ω) to connector E (black connector).

    CAUTION:
    Never connect the tester to the steering pad (driver side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1810, B1811, B1812, B1813, or 53 is not output.

    HINT:
    Codes other than DTC B1810, B1811, B1812, B1813, and 53 may be output at this time, but they are not related to this check.



NG
Go to step 3
OK

REPLACE STEERING PAD 

3.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT


    C173752E01
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect SST from connector E.

  1. Disconnect the instrument panel wire from the center airbag sensor assembly.

  1. Check for a short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery.

    2. Turn the ignition switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      z4-1 (D2-) - Body ground
      Ignition switch on (IG)
      Below 1 V
      z4-2 (D2+) - Body ground
      Ignition switch on (IG)
      Below 1 V

  1. Check for an open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      z4-1 (D2-) - z4-2 (D2+)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      z4-1 (D2-) - Body ground
      Always
      1 MΩ or higher
      z4-2 (D2+) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      z4-1 (D2-) - z4-2 (D2+)
      Always
      1 MΩ or higher



NG
Go to step 5
OK


4.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C167979E01
  1. Restore the released activation prevention mechanism of connector B to the original condition.

  1. Connect the connectors to the steering pad and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1810, B1811, B1812, B1813, or 53 is not output.

    HINT:
    Codes other than DTC B1810, B1811, B1812, B1813, and 53 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

5.CHECK INSTRUMENT PANEL WIRE


    C167977E04
  1. Restore the released activation prevention mechanism of connector B to the original condition.

  1. Disconnect the instrument panel wire from the spiral cable.

  1. Check for a short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery.

    2. Turn the ignition switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      D15-4 (D2+) - Body ground
      Ignition switch on (IG)
      Below 1 V
      D15-3 (D2-) - Body ground
      Ignition switch on (IG)
      Below 1 V

  1. Check for an open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      D15-4 (D2+) - D15-3 (D2-)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      D15-4 (D2+) - Body ground
      Always
      1 MΩ or higher
      D15-3 (D2-) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      D15-4 (D2+) - D15-3 (D2-)
      Always
      1 MΩ or higher



NG
REPLACE INSTRUMENT PANEL WIRE
OK


6.CHECK SPIRAL CABLE


    C167978E04
  1. Check for a short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery.

    2. Turn the ignition switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      z4-1 (D2-) - Body ground
      Ignition switch on (IG)
      Below 1 V
      z4-2 (D2+) - Body ground
      Ignition switch on (IG)
      Below 1 V

  1. Check for an open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      z4-1 (D2-) - z4-2 (D2+)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      z4-1 (D2-) - Body ground
      Always
      1 MΩ or higher
      z4-2 (D2+) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector D (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      z4-1 (D2-) - z4-2 (D2+)
      Always
      1 MΩ or higher



NG
REPLACE SPIRAL CABLE (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)