Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › VVT SENSOR

VVT SENSOR > REMOVAL

for Preparation Click here



1. REMOVE ENGINE UNDER COVER ASSEMBLY


    A171849
  1. Remove the 2 bolts and engine under cover assembly RR.



    A171850
  1. Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.



2. REMOVE NO. 1 ENGINE UNDER COVER


    A171855
  1. Remove the 6 bolts, 2 clips and No. 1 engine under cover.



3. DRAIN ENGINE COOLANT


  1. Loosen the radiator drain cock plug.


    A169414E01

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Remove the radiator cap sub-assembly from the radiator assembly.

    NOTICE:
    Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the 2 cylinder block drain cock plugs.



4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E150144
  1. Remove the nut, and the front wiper arm and blade assembly LH.



5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E150145
  1. Remove the nut, and the front wiper arm and blade assembly RH.



6. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E150146
  1. Disengage the 2 claws and disconnect the front fender to cowl side seal LH.



    E150147
  1. Disengage the 2 claws and disconnect the front fender to cowl side seal RH.



  1. Remove the 2 clips.


    E150149

  1. Disengage the 20 claws and remove the cowl top ventilator louver sub-assembly.



7. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    E150150
  1. Disconnect the connector.

  1. Remove the 4 bolts, and the windshield wiper motor and link assembly.



8. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY


    C165925
  1. Disengage the 4 clamps and separate the wiper wire harness from the outer cowl top panel sub-assembly.



    C165926
  1. Remove the 8 bolts, 6 nuts, and the outer cowl top panel sub-assembly.



9. REMOVE V-BANK COVER SUB-ASSEMBLY


    A162365
  1. Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the V-bank cover sub-assembly. Continue rising the V-bank cover sub-assembly to disengage the clip on the rear of the V-bank cover sub-assembly and remove the cover.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the V-bank cover sub-assembly to break.



10. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A170887
  1. Disconnect the 3 vacuum hoses.



    A170447
  1. Loosen the No. 1 air cleaner hose clamp.

  1. Disconnect the hose clamps and No. 2 ventilation hose.

  1. Disconnect the mass air flow meter connector.



    A170451
  1. Release the 2 clips, and remove the 2 bolts.

  1. Remove the air cleaner cap sub-assembly and air cleaner filter element.



11. DISCONNECT ENGINE ROOM MAIN WIRE


    A172968
  1. Disconnect the 5 harness clamps.



12. REMOVE NO. 1 SURGE TANK STAY


    A172967E01
  1. Remove the 2 bolts in the order shown in the illustration and remove the No. 1 surge tank stay.



13. REMOVE THROTTLE BODY BRACKET


    A172966E01
  1. Remove the 2 bolts in the order shown in the illustration and remove the throttle body bracket.



14. REMOVE INTAKE AIR SURGE TANK ASSEMBLY


    A171947E01
  1. Disconnect the 4 hoses.

    HINT:
    1. A: vapor feed hose
    2. B: union to check valve hose
    3. C: No. 1 ventilation hose
    4. D: vacuum hose



    A169363
  1. Disconnect the throttle body connector and clamp.

  1. Disconnect the connector.



    A169364
  1. Disconnect the 2 water by-pass hoses from the throttle body.



    A169366E02
  1. Remove the 4 bolts and 2 nuts in the order shown in the illustration.

    HINT:
    Use a 5 mm socket hexagon wrench to remove the 4 bolts.

  1. Remove the gasket from the intake air surge tank.



15. SEPARATE HARNESS PROTECTOR


  1. Remove the 5 bolts and nut [A].


    A171713E01

  1. Disconnect the 19 connectors [B].

  1. Disconnect the 2 clamps [C].

  1. Disconnect the 2 studs [D].



16. REMOVE VVT SENSOR (for Bank 1)


  1. Intake side:



      A171726
    1. Remove the bolt and VVT sensor.



  1. Exhaust side:



      A173952
    1. Remove the bolt and VVT sensor.



17. REMOVE VVT SENSOR (for Bank 2)


  1. Intake side:



      A135700
    1. Remove the bolt and VVT sensor.



  1. Exhaust side:



      A135699
    1. Remove the bolt and VVT sensor.