DTC P0013 Camshaft Position "B" Actuator Circuit / Open (Bank 1) |
DTC P0023 Camshaft Position "B" Actuator Circuit / Open (Bank 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0013 | Open or short in camshaft timing oil control valve for exhaust camshaft (bank 1) circuit (1 trip detection logic) |
|
| P0023 | Open or short in camshaft timing oil control valve for exhaust camshaft (bank 2) circuit (1 trip detection logic) |
|
| Related DTCs | P0013: VVT OCV (bank 1) open/short P0023: VVT OCV (bank 2) open/short |
| Required sensors / components (Main) | VVT OCV (Variable Valve Timing oil control valve) |
| Required sensors / components (Sub) | - |
| Frequency of operation | Continuous |
| Duration | 1 second |
| MIL operation | Immediate |
| Sequence of operation | None |
| The monitor will run whenever these DTCs are not present | None |
| All of the following conditions are met | - |
| Starter | OFF |
| Ignition switch | ON |
| Time after ignition switch off to on | 0.5 seconds or more |
| One of the following conditions is met: | Condition A, B or C |
| A. All of the following conditions are met | - |
| Battery voltage | 11 to 13 V |
| Target duty ratio | Less than 70% |
| Current cut status | Not cut |
| B. All of the following conditions are met: | - |
| Battery voltage | 13 V or more |
| Target duty ratio | Less than 80% |
| Current cut status | Not cut |
| Exhaust VVT oil control valve condition | No operation record |
| Exhaust VVT oil control valve condition | No operation record |

| 1.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OIL CONTROL VALVE FOR INTAKE CAMSHAFT) |
Connect the Techstream to the DLC3.
Start the engine and turn the tester on.
Warm up the engine.
Select the following menus: Powertrain/ Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank 1) or Control the VVT Exhaust Linear (Bank 2).
Check the engine speed while operating the oil control valve using the tester.
| Tester Operation | Specified Condition |
| -128% (Oil control valve OFF) | Normal engine speed |
| 127% (Oil control valve ON) | Engine idles roughly or stalls (soon after oil control valve switched from OFF to ON) |
|
| ||||
| OK | ||
| ||
| 2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
![]() |
Disconnect the exhaust camshaft timing oil control valve connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 6.9 to 7.9 Ω |
Reconnect the camshaft timing oil control valve connector.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE - ECM) |
![]() |
Disconnect the exhaust camshaft timing oil control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B3-26 (OE1+) - B44-1 | Always | Below 1 Ω |
| B3-31 (OE1-) - B44-2 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B3-27 (OE2+) - B41-1 | Always | Below 1 Ω |
| B3-32 (OE2-) - B41-2 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B3-26 (OE1+) or B44-1 - Body ground | Always | 10 kΩ or higher |
| B3-31 (OE1-) or B44-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| B3-27 (OE2+) or B41-1 - Body ground | Always | 10 kΩ or higher |
| B3-32 (OE2-) or B41-2 - Body ground | Always | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the camshaft timing oil control valve connector.
|
| ||||
| OK | ||
| ||