VEHICLE STABILITY CONTROL SYSTEM > SYSTEM DESCRIPTION |
| FUNCTION DESCRIPTION |
ABS (Anti-lock Brake System)
The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface.

Operation description
The skid control ECU detects wheel lock based on speed signals received from the wheel speed sensors. Based on this information, the skid control ECU controls the pump motor and solenoid valves. The pump motor and solenoid valves are used to prevent wheel lock by controlling the hydraulic pressure applied to the brakes at each wheel. The ABS warning light will come on when the system is malfunctioning.
EBD (Electronic Brake force Distribution)
The EBD control utilizes ABS, and performs proper brake force distribution between the front and rear wheels in accordance with driving conditions.
When braking while cornering, it also controls the brake force distribution between the right and left wheels, helping to maintain vehicle behavior.

Operation description
The skid control ECU receives a speed signal from each wheel speed sensor, and uses these signals to detect locking of the wheels. The ECU uses this information in order to determine appropriate control of the solenoid valves.
The solenoid valves control the hydraulic pressure applied to the brake cylinder at each wheel. In this way, the solenoid valves are used to control the brake power split between the front and rear, and left and right wheels. The ABS warning and brake warning lights will come on if there is a malfunction in the EBD system.
BA (Brake Assist)
The primary purpose of the brake assist system is to provide auxiliary brake force to assist a driver who cannot generate a large enough brake force during emergency braking, thus helping to maximize the brake performance of the vehicle.

Operation description
The skid control ECU receives a speed signal from each speed sensor and a fluid pressure signal from the master cylinder pressure sensor to determine whether brake assist is necessary. If brake assist is necessary, the skid control ECU sends control signals to the pump motor and solenoid. The pump and the solenoid valves then control the pressure applied to each wheel cylinder.
The ABS warning light will come on to indicate a malfunction in the BA system.
TRAC (Traction Control)
The TRAC system helps prevent the drive wheels from slipping when the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface.

Operation description
The skid control ECU detects wheelspin by receiving signals from each speed sensor and the ECM via CAN communication. The skid control ECU sends signals via CAN communication to the ECM in order to control engine torque. The skid control ECU controls brake hydraulic pressure using the pump and solenoid valves.
The slip indicator light blinks when the system is operating. When there is a malfunction in the TRAC system, the slip indicator light will come on.
The VSC OFF switch stops traction control operation. If TRAC control is turned off, the TRAC OFF indicator light will come on.
VSC (Vehicle Stability Control)
The VSC system helps prevent the vehicle from slipping sideways as a result of strong front or rear wheel skid during cornering.

Operation description
The skid control ECU determines the vehicle operating conditions based on signals received from the wheel speed sensors, yaw rate and acceleration sensor, and steering angle sensor. The skid control ECU sends signals via CAN communication to the ECM in order to control engine torque. The skid control ECU controls brake hydraulic pressure using the pump and solenoid valves.
The slip indicator light blinks, and the skid control buzzer sounds when the system is operating. If a malfunction occurs in the VSC system, the slip indicator light will come on.
The VSC OFF switch stops VSC control operation. If VSC control is turned off, the VSC OFF indicator light will come on.
| DOWNHILL ASSIST CONTROL (for 4WD) |
The downhill assist control generates four-wheel hydraulic pressure when the downhill assist control switch is pressed and the accelerator and brake pedals are not depressed in order to maintain a constant low vehicle speed while preventing wheel lock.
| HILL-START ASSIST CONTROL |
The hill-start assist control generates four-wheel hydraulic pressure when the brake pedal is further depressed while the vehicle is stationary in order to prevent the vehicle from moving backward.
| COOPERATIVE CONTROL (ENHANCED-VSC) FUNCTION |
Braking control on split friction roads
When braking on a split friction road, the vehicle tends to deflect toward the higher friction side due to the difference between the braking forces on the left and right sides. With Enhanced-VSC, the power steering ECU receives command signals from the skid control ECU. Based on these signals, the power steering ECU operates the motor for the electronic power steering to reduce the effect of the difference between the braking forces on the left and right sides, assisting steering operation. This enables the driver to make steering corrections more easily.
Accelerating when surface resistance differs between both sides of wheels
When accelerating on a split friction road, the vehicle tends to deflect toward lower friction side due to the driving force difference between the left and right sides. With Enhanced-VSC, the skid control ECU performs braking control of the drive wheel on the low friction side (traction control function) and transmits command signals to the power steering ECU. Based on these signals, the power steering ECU operates the motor for the electronic power steering to reduce the effect of the driving force difference between the left and right sides, assisting steering operation. As a result, proper motive force and vehicle stability is ensured.
Front wheel skid control
When front wheel skidding is detected, engine output is limited and braking control is performed based on the amount of understeer tendency. Accordingly, a moment of force is generated in the vehicle turning direction to limit front wheel skid tendency.
When the skid control ECU determines that there is a front wheel skid tendency, it controls the VSC to dampen the front wheel skid. At the same time, it effects cooperative control with the electronic power steering to provide steering torque assist, which facilitates the driver's steering maneuvers to stabilize the vehicle posture. The system also provides steering torque assist to prevent excessive steering maneuvers. This assist increases the resistance to counter the driver's steering effort if they turn the steering wheel excessively.
Rear wheel skid control
When rear wheel skidding is detected, brake force is applied to mainly the outer wheels according to the amount of oversteer tendency. Accordingly, an anti-spin moment is generated to limit the rear wheel skid tendency.
With Enhanced-VSC, the power steering ECU receives command signals from the skid control ECU. Based on these signals, the power steering ECU operates the motor for the electronic power steering to provide steering assist to help the driver compensate for the rear wheel skid tendency. This enables the driver to operate the steering wheel more easily.
| ABS with EBD, BA, TRAC and VSC OPERATION |
The skid control ECU calculates vehicle stability tendency based on signals from the speed sensor, yaw rate and acceleration sensor, and steering angle sensor. In addition, it evaluates the results of the calculations to determine whether any control actions (control of the engine output torque by electronic throttle control and of the wheel brake pressure by the brake actuator assembly) should be implemented.
The slip indicator blinks and the skid control buzzer sounds to inform the driver that the VSC system is operating. The slip indicator also blinks when traction control is operating, and the operation being performed is displayed.
| FAIL SAFE |
When a failure occurs in the ABS with BA, TRAC and VSC systems, the ABS warning and slip indicator lights come on, and the ABS with BA, TRAC and VSC operations are prohibited. In addition, when there is a failure that disables EBD operation, the brake warning light also comes on and EBD operation is prohibited.
If control is prohibited due to a malfunction during operation, control will be disabled gradually.
This is to avoid sudden vehicle instability.
| INITIAL CHECK |
When the vehicle speed first reaches approximately 6 km/h (4 mph) after the ignition switch is turned on (IG), each solenoid valve and motor of the brake actuator are sequentially activated to perform an electrical check. During the initial check, the operating sound of the solenoid valves and motor can be heard from the engine compartment, but this is not a malfunction.
| INSPECTION MODE |
TRAC and VSC operation can be disabled by operating Techstream (Click here).
| FUNCTION OF COMPONENTS |
| Components | Function |
| Speed sensor | Detects the wheel speed and sends the signal to the skid control ECU. |
| Yaw rate and acceleration sensor |
|
| Steering angle sensor |
|
| Stop light switch | Detects the brake operating conditions and inputs the signals to the skid control ECU. |
| Brake pedal load sensing switch |
|
| Parking brake switch | Detects the parking brake operating conditions and inputs the signals to the skid control ECU. |
| Master cylinder pressure sensor |
|
| Skid control ECU |
|
| Brake actuator assembly |
|
| ABS motor relay |
|
| ABS motor fail safe relay |
|
| ABS solenoid relay |
|
| Stop light control relay | Turns on the stop lights during downhill assist control (for 4WD) or hill-start assist control operation. |
| ABS warning light |
|
| Brake warning light |
|
| VSC OFF indicator light | Comes on to inform the driver when the VSC off mode is entered using the VSC OFF switch. |
| TRAC OFF indicator light | Comes on to inform the driver when the TRAC off mode is entered using the VSC OFF switch. |
| Slip indicator light |
|
| Downhill assist control indicator light (*1) |
|
| Master caution indicator light (*2) | Comes on to inform the driver that a malfunction in the brake control system has occurred. |
| Multi-information display (*2) |
|
| Skid control buzzer |
|
| ECM | Controls the engine output when TRAC and/or VSC are operating according to the signals sent from the skid control ECU via CAN communication. |
| VSC OFF switch | Pressing this switch turns off TRAC and pressing and holding this switch turns off TRAC and VSC. |
| Downhill assist control switch (*1) | Pressing this switch turns downhill assist control ON or OFF. |