Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > CHECK FOR INTERMITTENT PROBLEMS

for Preparation Click here



CHECK FOR INTERMITTENT PROBLEMS

HINT:
A momentary interruption (open circuit) in the connectors and/or wire harnesses between the sensors and ECUs can be detected using the ECU Data List function of Techstream.

  1. Turn the ignition switch off.

  2. Connect Techstream to the DLC3.

  3. Turn the ignition switch on (IG).

  4. Turn Techstream on.



  5. C154775E06
  6. Follow the directions on Techstream to display the Data List and select areas where momentary interruptions should be monitored.

    HINT:
    1. A momentary interruption (open circuit) cannot be detected for 3 seconds after the ignition switch is turned on (IG) (initial check).
    2. If the ERROR display remains displayed, check for continuity between the ECUs and the sensors, or between ECUs.
    3. The ERROR display on Techstream will remain displayed for 1 second after the harness signal changes from momentary interruption (open circuit) to normal condition.


    ABS / VSC / TRAC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Speed Open
    FR speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    FL Speed Open
    FL speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    RR Speed Open
    RR speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    RL Speed Open
    RL speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    EFI Communication Open
    EFI communication open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    Yaw Rate Open
    Yaw rate sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    Deceleration Open
    Acceleration sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    Steering Open
    Steering angle sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    Master Cylinder Open
    Master cylinder pressure sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    IG Voltage Value Decreased
    IG voltage value decrease detection / ERROR or NORMAL
    ERROR: Decrease
    NORMAL: Normal
    -
    IG Voltage Value Increased
    IG voltage value increase detection / ERROR or NORMAL
    ERROR: Increase
    NORMAL: Normal
    -
    FR Speed Sensor Voltage Open
    FR speed sensor voltage open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    FL Speed Sensor Voltage Open
    FL speed sensor voltage open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    RR Speed Sensor Voltage Open
    RR speed sensor voltage open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    RL Speed Sensor Voltage Open
    RL speed sensor voltage open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    M/C Pressure Sensor Noise
    Master cylinder pressure sensor noise detection / ERROR or NORMAL
    ERROR: Malfunction
    NORMAL: Normal
    -
    Brake Pedal Switch Open
    Brake pedal load sensing switch open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    Yaw Rate Sensor Voltage Open
    Yaw rate sensor voltage open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    EFI Communication Invalid
    EFI communication invalid detection / ERROR or NORMAL
    ERROR: Invalid
    NORMAL: Normal
    -



  7. F047126
  8. While observing the screen, gently jiggle the connectors or wire harnesses between the ECUs and sensors, or between ECUs.

    OK:
    NORMAL display appears.

    HINT:
    The connector and/or wire harness has a momentary interruption (open circuit) if the display changes. Repair or replace the connectors and/or wire harnesses as one of them is faulty.