Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect Techstream to the DLC3.

  4. Turn the ignition switch on (IG).

  5. Turn Techstream on.

  6. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

  7. According to the display on the tester, read the Data List.

    ABS / VSC / TRAC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ABS Warning Light
    ABS warning light / ON or OFF
    ON: Warning light ON
    OFF: Warning light OFF
    -
    Brake Warning Light
    Brake warning light / ON or OFF
    ON: Warning light ON
    OFF: Warning light OFF
    -
    Slip Indicator Light
    Slip indicator light / ON or OFF
    ON: Indicator light ON
    OFF: Indicator light OFF
    -
    Downhill Assist Control Light (*1)
    Downhill assist control indicator light / ON or OFF
    ON: Indicator light ON
    OFF: Indicator light OFF
    -
    Buzzer
    Skid control buzzer / ON or OFF
    ON: Buzzer ON
    OFF: Buzzer OFF
    -
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Parking Brake SW
    Parking brake switch / ON or OFF
    ON: Parking brake applied
    OFF: Parking brake released
    -
    Main Idle SW
    Main idle switch / ON or OFF
    ON: Accelerator pedal released
    OFF: Accelerator pedal depressed
    -
    Brake Pedal Load Sensing SW
    Brake pedal load sensing switch / ON or OFF
    ON: Brake pedal depressed beyond the specified point
    OFF: Brake pedal not depressed beyond the specified point
    -
    Gear Position
    Gear position information / P/N, R, 1st-8th, FAIL, NOT R
    Actual gear position
    -
    Shift Lever Position
    Shift lever position information / P/N, R, D/M, 1st-6th/B, FAIL
    Actual shift lever position
    -
    Shift Information
    Shift information / ON or OFF
    ON: During gear change
    -
    Inspection Mode
    Inspection mode / OTHER or INSPECT
    OTHER: Normal mode
    INSPECT: Inspection mode
    -
    Number of IG ON (Inspection)
    Number of ignition switch being turned on (IG) after entering inspection mode / min.: 0, max.: 255
    Min.: 0
    Max.: 255
    -
    Downhill Assist Control SW (*1)
    Downhill assist control switch / ON or OFF
    ON: Switch ON
    OFF: Switch OFF
    -
    Master Cylinder Sensor
    Master cylinder pressure sensor / min.: 0 V, max.: 5 V
    When brake pedal is released: 0.3 to 0.9 V
    Reading increases when brake pedal is depressed
    Zero Point of M/C
    Memorized zero value / min.: -12.5 MPa, max.: 12.4 MPa
    Min.: -12.5 MPa
    Max.: 12.4 MPa
    -
    Deceleration Sensor
    Acceleration sensor / min.: -18.52 m/s2, max.: 18.39 m/s2
    Min.: -18.52 m/s2
    Max.: 18.39 m/s2
    Reading changes when vehicle is bounced
    Zero Point of Decele
    Memorized zero value / min.: -25.11 m/s2, max.: 24.91 m/s2
    Min.: -25.11 m/s2
    Max.: 24.91 m/s2
    -
    Deceleration Sensor 2
    Acceleration sensor 2 / min.: -18.52 m/s2, max.: 18.39 m/s2
    Min.: -18.52 m/s2
    Max.: 18.39 m/s2
    Reading changes when vehicle is bounced
    Zero Point of Decele 2
    Memorized zero value / min.: -25.11 m/s2, max.: 24.91 m/s2
    Min.: -25.11 m/s2
    Max.: 24.91 m/s2
    -
    Yaw Rate Sensor
    Yaw rate sensor / min.: -128 deg/s, max.: 127 deg/s
    Vehicle stationary: 0 deg/s
    Right turn: -128 to 0 deg/s
    Left turn: 0 to 127 deg/s
    -
    Zero Point of Yaw Rate
    Memorized zero value / min.: -128 deg/s, max.: 127 deg/s
    Min.: -128 deg/s
    Max.: 127 deg/s
    -
    Yaw Rate Sensor 2
    Yaw rate sensor 2 / min.: -128 deg/s, max.: 127 deg/s
    Vehicle stationary: 0 deg/s
    Right turn: -128 to 0 deg/s
    Left turn: 0 to 127 deg/s
    -
    Zero Point of Yaw Rate 2
    Memorized zero value / min.: -128 deg/s, max.: 127 deg/s
    Min.: -128 deg/s
    Max.: 127 deg/s
    -
    Steering Angle Sensor
    Steering angle sensor / min.: -3276.8 deg, max.: 3276.7 deg
    Left turn: Increase
    Right turn: Decrease
    -
    Zero Point of Steering Angle
    Memorized zero value / min.: -3276.8 deg, max.: 3276.7 deg
    Min.: -3276.8 deg
    Max.: 3276.7 deg
    -
    Lateral G
    Lateral G / min.: -25.11 m/s2, max.: 24.91 m/s2
    Min.: -25.11 m/s2
    Max.: 24.91 m/s2
    -
    Forward and Rearward G
    Forward and backward G / min.: -25.11 m/s2, max.: 24.91 m/s2
    Min.: -25.11 m/s2
    Max.: 24.91 m/s2
    -
    Yaw Rate Value
    Yaw rate value / min.: -128 deg/s, max.: 127 deg/s
    Min.: -128 deg/s
    Max.: 127 deg/s
    -
    Steering Angle Value
    Steering angle value / min.: -3276.8 deg, max.: 3276.7 deg
    Min.: -3276.8 deg
    Max.: 3276.7 deg
    -
    Stop Light Relay (*2)
    Stop light control relay / ON or OFF
    ON: Relay ON
    OFF: Relay OFF
    -
    FR Wheel Speed
    FR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    Similar speed as indicated on speedometer
    FL Wheel Speed
    FL wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    Similar speed as indicated on speedometer
    RR Wheel Speed
    RR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    Similar speed as indicated on speedometer
    RL Wheel Speed
    RL wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    Similar speed as indicated on speedometer
    Vehicle Speed
    Maximum wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual vehicle speed
    Speed indicated on speedometer
    FR Wheel Acceleration
    FR wheel acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2
    0 m/s2
    -
    FL Wheel Acceleration
    FL wheel acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2
    0 m/s2
    -
    RR Wheel Acceleration
    RR wheel acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2
    0 m/s2
    -
    RL Wheel Acceleration
    RL wheel acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2
    0 m/s2
    -
    Stop Light Relay Output (*2)
    Stop light control relay output / ON or OFF
    ON: Relay output ON
    OFF: Relay output OFF
    -
    FR Wheel ABS Ctrl Status
    FRL wheel ABS control status / ON or OFF
    ON: During control
    -
    FL Wheel ABS Ctrl Status
    FL wheel ABS control status / ON or OFF
    ON: During control
    -
    RR Wheel ABS Ctrl Status
    RR wheel ABS control status / ON or OFF
    ON: During control
    -
    RL Wheel ABS Ctrl Status
    RL wheel ABS control status / ON or OFF
    ON: During control
    -
    RR Wheel EBD Ctrl Status
    RR wheel EBD control status / ON or OFF
    ON: During control
    -
    RL Wheel EBD Ctrl Status
    RL wheel EBD control status / ON or OFF
    ON: During control
    -
    BA Ctrl Status
    BA control status / ON or OFF
    ON: During control
    -
    TRC (TRAC) Ctrl Status
    TRAC control status / ON or OFF
    ON: During control
    -
    TRC (TRAC) Engine Ctrl Status
    TRAC engine control status / ON or OFF
    ON: During control
    -
    TRC (TRAC) Brake Ctrl Status
    TRAC brake control status / ON or OFF
    ON: During control
    -
    FR Wheel VSC Ctrl Status
    FR wheel VSC control status / ON or OFF
    ON: During control
    -
    FL Wheel VSC Ctrl Status
    FL wheel VSC control status / ON or OFF
    ON: During control
    -
    RR Wheel VSC Ctrl Status
    RR wheel VSC control status / ON or OFF
    ON: During control
    -
    RL Wheel VSC Ctrl Status
    RL wheel VSC control status / ON or OFF
    ON: During control
    -
    Engine Revolutions
    Engine revolutions / min.: 0 r/min, max.: 65535 r/min
    Min..: 0 r/min
    Max.: 65535 r/min
    -
    Real Engine Torque
    Real engine torque / min.: -1024 N*m, max.: 1023 N*m
    Min.: -1024 N*m
    Max.: 1023 N*m
    -
    Accelerator Opening Angle %
    The difference of a present accelerator / min.: 0 %, max.: 128 %
    Min.: 0 %
    Max.: 128 %
    -
    Solenoid Relay
    ABS solenoid relay / ON or OFF
    ON: Solenoid relay ON
    OFF: Solenoid relay OFF
    -
    ABS Motor Relay
    ABS motor relay / ON or OFF
    ON: Motor relay ON
    OFF: Motor relay OFF
    -
    Fail Safe Motor Relay
    ABS motor fail safe relay / ON or OFF
    ON: Motor relay ON
    OFF: Motor relay OFF
    -
    TR(A)C/VSC Solenoid (SM2)
    Master cut solenoid (SM2) / ON or OFF
    ON: Operates
    -
    TR(A)C/VSC Solenoid (SM1)
    Master cut solenoid (SM1) / ON or OFF
    ON: Operates
    -
    ABS Solenoid (SFRH)
    ABS solenoid (SFRH) / ON or OFF
    ON: Operates
    -
    ABS Solenoid (SFRR)
    ABS solenoid (SFRR) / ON or OFF
    ON: Operates
    -
    ABS Solenoid (SFLH)
    ABS solenoid (SFLH) / ON or OFF
    ON: Operates
    -
    ABS Solenoid (SFLR)
    ABS solenoid (SFLR) / ON or OFF
    ON: Operates
    -
    ABS Solenoid (SRRH)
    ABS solenoid (SRRH) / ON or OFF
    ON: Operates
    -
    ABS Solenoid (SRRR)
    ABS solenoid (SRRR) / ON or OFF
    ON: Operates
    -
    ABS Solenoid (SRLH)
    ABS solenoid (SRLH) / ON or OFF
    ON: Operates
    -
    ABS Solenoid (SRLR)
    ABS solenoid (SRLR) / ON or OFF
    ON: Operates
    -
    FR Speed Open
    FR speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    FL Speed Open
    FL speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    RR Speed Open
    RR speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    RL Speed Open
    RL speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    EFI Communication Open
    EFI communication open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    Yaw Rate Open
    Yaw rate sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    Deceleration Open
    Acceleration sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    Steering Open
    Steering angle sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    Master Cylinder Open
    Master cylinder pressure sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    MT Voltage Value
    Motor driving monitor voltage / min.: 0 V, max.: 255 V
    Min.: 0 V
    Max.: 255 V
    -
    TRC/VSC Off Mode
    VSC OFF switch / NORMAL, TRC OFF or VSC OFF
    NORMAL: Normal mode
    TRC OFF: TRAC off mode
    VSC OFF: VSC off mode
    -
    Number of DTC
    Number of DTC recorded / min.: 0, max.: 255
    Min.: 0
    Max.: 255
    -
    IG Voltage Value Decreased
    IG voltage value decrease detection / ERROR or NORMAL
    ERROR: Decrease
    NORMAL: Normal
    -
    IG Voltage Value Increased
    IG voltage value increase detection / ERROR or NORMAL
    ERROR: Increase
    NORMAL: Normal
    -
    FR Speed Sensor Voltage Open
    FR speed sensor voltage open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    FL Speed Sensor Voltage Open
    FL speed sensor voltage open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    RR Speed Sensor Voltage Open
    RR speed sensor voltage open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    RL Speed Sensor Voltage Open
    RL speed sensor voltage open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    M/C Pressure Sensor Noise
    Master cylinder pressure sensor noise detection / ERROR or NORMAL
    ERROR: Malfunction
    NORMAL: Normal
    -
    Brake Pedal Switch Open
    Brake pedal load sensing switch open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    Yaw Rate Sensor Voltage Open
    Yaw rate sensor voltage open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    EFI Communication Invalid
    EFI communication invalid detection / ERROR or NORMAL
    ERROR: Invalid
    NORMAL: Normal
    -
    (*1): for 4WD
    (*2): with downhill assist control (for 4WD) or hill-start assist control


ACTIVE TEST

HINT:
Using Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts to operate without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect Techstream to the DLC3.

  4. Turn the ignition switch on (IG).

  5. Turn Techstream on.

  6. Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.

  7. According to the display on the tester, perform the Active Test.

    ABS / VSC / TRAC: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    ABS Warning Light
    ABS warning light
    Warning light ON / OFF
    Observe combination meter
    Brake Warning Light
    Brake warning light
    Warning light ON / OFF
    Observe combination meter
    Slip Indicator Light
    Slip indicator light
    Indicator light ON / OFF
    Observe combination meter
    VSC OFF Indicator Light
    VSC OFF indicator light
    Indicator light ON / OFF
    Observe combination meter
    TRAC OFF Indicator Light
    TRAC OFF indicator light
    Indicator light ON / OFF
    Observe combination meter
    Downhill Assist Control Light (*1)
    Downhill assist control indicator light
    Indicator light ON / OFF
    Observe combination meter
    Buzzer
    Skid control buzzer
    Buzzer ON / OFF
    Buzzer can be heard
    Solenoid Relay
    ABS solenoid relay
    Relay ON / OFF
    -
    Motor Relay
    ABS motor relay
    Relay ON / OFF
    Operating sound of motor can be heard
    Stop Light Relay (*2)
    Stop light control relay
    Relay ON / OFF
    Stop lights come on
    ABS Solenoid (SRLR)
    ABS solenoid (SRLR)
    Solenoid ON / OFF
    Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SRLH)
    ABS solenoid (SRLH)
    Solenoid ON / OFF
    Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SRRR)
    ABS solenoid (SRRR)
    Solenoid ON / OFF
    Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SRRH)
    ABS solenoid (SRRH)
    Solenoid ON / OFF
    Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SFLR)
    ABS solenoid (SFLR)
    Solenoid ON / OFF
    Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SFLH)
    ABS solenoid (SFLH)
    Solenoid ON / OFF
    Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SFRR)
    ABS solenoid (SFRR)
    Solenoid ON / OFF
    Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SFRH)
    ABS solenoid (SFRH)
    Solenoid ON / OFF
    Operating sound of solenoid (clicking sound) can be heard
    VSC/TRC Solenoid (SMR)
    Master cut solenoid (SM2)
    Solenoid ON / OFF
    Operating sound of solenoid (clicking sound) can be heard
    VSC/TRC Solenoid (SMF)
    Master cut solenoid (SM1)
    Solenoid ON / OFF
    Operating sound of solenoid (clicking sound) can be heard
    (*1): for 4WD
    (*2): with downhill assist control (for 4WD) or hill-start assist control