Home › ENGINE › 2GR-FE STARTING › SMART KEY SYSTEM

SMART KEY SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the DATA LIST information early in troubleshooting is one way to save diagnostic time.

  1. Connect Techstream to the DLC3.
    When using Techstream with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 or less second intervals until communication between the tester and vehicle starts.

  2. Turn the engine switch on (IG).

  3. Read the DATA LIST.

    Main Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ACC SW
    Engine switch on (ACC) / ON or OFF
    ON: Engine switch on (ACC)
    OFF: Engine switch off
    -
    IG SW
    Engine switch on (IG) / ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    St SW1
    Start switch 1 / ON or OFF
    ON: Engine switch is pushed
    OFF: Engine switch is not pushed
    -
    St SW2
    Start switch 2 / ON or OFF
    ON: Engine switch is pushed
    OFF: Engine switch is not pushed
    -
    Str Unlock SW
    Steering lock condition / ON or OFF
    ON: Steering is unlocked (Engine switch on (ACC))
    OFF: Steering is locked (Engine switch off)
    -
    N SW / C SW
    Park/Neutral position switch / ON or OFF
    ON: Shift position is P or N
    OFF: Shift position is except P and N
    -
    SHIFT P SIG
    Shift P position signal / ON or OFF
    ON: Shift position is P
    OFF: Shift position is not P
    -
    Vehicle Spd Sig
    Vehicle speed signal / STOP or RUN
    STOP: Vehicle is stopped
    RUN: Vehicle is running
    -
    E/G Cond
    Engine condition / STOP or RUN
    STOP: Engine is stopped
    RUN: Engine is running
    -
    IG1 Relay Mon1
    IG1 relay monitor (outer) / ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -
    IG2 Relay Mon1
    IG2 relay monitor (outer) / ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -
    IG1 Relay Mon2
    IG1 relay monitor (inner) / ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -
    IG2 Relay Mon2
    IG2 relay monitor (inner) / ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -
    ACC Relay Mon
    ACC relay monitor / ON or OFF
    ON: Engine switch on (ACC)
    OFF: Engine switch off
    -
    Latch Circuit
    Ratch circuit / ON or OFF
    ON: Engine switch on (IG) or engine is running
    OFF: Engine switch off or on (ACC)
    -
    Start Req Sig
    Starter request signal monitor / ON or OFF
    ON: Starter relay is ON
    OFF: Starter relay is OFF
    Engine switch pressed and held with shift lever in P or N
    Pwr Cond
    Power supply condition / ALL, ACC ON, IG1 IG2, ST ON
    ALL: All relays are OFF
    ACC ON: ACC relay is ON
    IG1: IG1 relay is ON
    IG2: IG2 relay is ON
    ST ON: ST request signal is ON
    -
    ACC Cut Sig
    ACC relay cut signal / ON or OFF
    ON: Engine is cranking
    OFF: Engine is not cranking
    -
    St Relay Mon
    STARTER relay monitor / ON or OFF
    ON: Engine is cranking
    OFF: Engine is not cranking
    Engine is cranking with engine switch on (IG) and shift lever in P or N
    Comm Smrt/Wrls
    Communication for certification ECU (smart key ECU assembly) / OK or STOP
    OK: Communication
    STOP: No communication
    -


PERFORM ACTIVE TEST

HINT:
Using Techstream to perform ACTIVE TEST allows the relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing the ACTIVE TEST early in troubleshooting is one way to save diagnostic time. The DATA LIST can be displayed while performing ACTIVE TESTs.

  1. Connect Techstream to the DLC3.

  2. Turn the engine switch on (IG).

  3. Perform the ACTIVE TEST according to the display on the tester.


Main Body: 
Tester Display
Test Part
Control Range
Diagnostic Note
Lighting Ind
Indicator for lighting
ON / OFF
-
Ind Condition
Engine switch indicator
Green / Amber / No Sig
-
S Lock Pwr
Power supply for steering lock ECU
ON / OFF
-