Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here


NOTICE:
  1. Turn the ignition switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
  2. After the ignition switch is turned off, check that the key reminder warning system and light remainder warning system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches, or the doors. If any doors need to be opened in order to check the connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any other switches, or a door triggers related ECU and sensor communication on the CAN.
This communication will cause the resistance value to change.

NOTICE:
This section describes the standard CAN values for all CAN related components.


JUNCTION CONNECTOR FOR CAN BUS


  1. CAN junction connector CTR


    C132298E25


    CAN Junction Connector CTR
    Wiring Color
    Connect to
    D55-1 (CANH)
    SB
    CAN junction connector RH
    D55-12 (CANL)
    W
    CAN junction connector RH
    D55-2 (CANH)
    V
    Yaw rate sensor
    D55-13 (CANL)
    W
    Yaw rate sensor
    D55-3 (CANH)
    Y
    Center airbag sensor assembly
    D55-14 (CANL)
    W
    Center airbag sensor assembly
    D55-4 (CANH)
    L
    DLC3
    D55-15 (CANL)
    W
    DLC3
    D55-5 (CANH)
    R
    Steering angle sensor
    D55-16 (CANL)
    W
    Steering angle sensor
    D55-6 (CANH)
    P
    Combination meter
    D55-17 (CANL)
    W
    Combination meter
    D55-7 (CANH)
    BR
    Power steering ECU
    D55-18 (CANL)
    W
    Power steering ECU
    D55-8 (CANH)
    GR
    Main body ECU
    D55-19 (CANL)
    W
    Main body ECU



  2. CAN junction connector RH


    C132298E24


    CAN Junction Connector RH
    Wiring Color
    Connect to
    D59-1 (CANH)
    R
    ECM
    D59-12 (CANL)
    W
    ECM
    D59-2 (CANH)
    BR
    Accessory gateway
    D59-13 (CANL)
    W
    Accessory gateway
    D59-3 (CANH)
    LG
    Air conditioning amplifier
    D59-14 (CANL)
    W
    Air conditioning amplifier
    D59-4 (CANH)
    B
    Skid control ECU
    D59-15 (CANL)
    W
    Skid control ECU
    D59-5 (CANH)
    SB
    CAN junction connector CTR
    D59-16 (CANL)
    W
    CAN junction connector CTR



  3. The connection diagram of the components which are connected to the CAN junction connector.


    C169643E01


JUNCTION CONNECTOR FOR CAN MS BUS (w/ POWER BACK DOOR SYSTEM)


  1. CAN junction connector RR


    C167481E08


    CAN Junction Connector RR
    Wiring Color
    Connect to
    O21-1 (CANH)
    B
    Back door ECU*2
    O21-2 (CANL)
    W
    Back door ECU*2
    O23-1 (CANH)
    GR
    Certification ECU*1
    O23-2 (CANL)
    W
    Certification ECU*1
    O24-1 (CANH)
    Y
    Main body ECU*2
    O24-2 (CANL)
    W
    Main body ECU*2

    HINT:
    1. *1: w/ Smart key system and power back door system.
    2. *2: w/ Power back door system.



  2. The connection diagram of the components which are connected to the CAN junction connector.


    C169644E02


DLC3


    C125062E12
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    D47-6 (CANH) - D47-14 (CANL)
    L - W
    Ignition switch off
    54 to 69 Ω
    D47-6 (CANH) - D47-4 (CG)
    L - B
    Ignition switch off
    200 Ω or higher
    D47-14 (CANL) - D47-4 (CG)
    W - B
    Ignition switch off
    200 Ω or higher
    D47-6 (CANH) - D47-16 (BAT)
    L - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D47-14 (CANL) - D47-16 (BAT)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher


SKID CONTROL ECU WITH ACTUATOR


    C156384E47
  1. Disconnect the connector from the skid control ECU.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    A24-25 (CANH) - A24-14 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    A24-25 (CANH) - A24-1 (GND1)
    B - W-B
    Ignition switch off
    200 Ω or higher
    A24-14 (CANL) - A24-1 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    A24-25 (CANH) - A24-24 (BM)
    B - B
    Negative battery terminal disconnected
    6 kΩ or higher
    A24-14 (CANL) - A24-24 (BM)
    W - B
    Negative battery terminal disconnected
    6 kΩ or higher


STEERING ANGLE SENSOR


    C146385E02
  1. Disconnect the connector from the steering angle sensor.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    D14-3 (CANH) - D14-2 (CANL)
    R - W
    Ignition switch off
    54 to 69 Ω
    D14-3 (CANH) - D14-1 (ESS)
    R - GR
    Ignition switch off
    200 Ω or higher
    D14-2 (CANL) - D14-1 (ESS)
    W - GR
    Ignition switch off
    200 Ω or higher
    D14-3 (CANH) - D14-5 (BAT)
    R - BR
    Negative battery terminal disconnected
    6 kΩ or higher
    D14-2 (CANL) - D14-5 (BAT)
    W - BR
    Negative battery terminal disconnected
    6 kΩ or higher


YAW RATE SENSOR


    C152858E03
  1. Disconnect the connector from the yaw rate sensor.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    O6-3 (CANH) - O6-2 (CANL)
    V - W
    Ignition switch off
    54 to 69 Ω
    O6-3 (CANH) - O6-1 (GND)
    V - W-B
    Ignition switch off
    200 Ω or higher
    O6-2 (CANL) - O6-1 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    O6-3 (CANH) - D47-16 (BAT)
    V - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    O6-2 (CANL) - D47-16 (BAT)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher


CENTER AIRBAG SENSOR ASSEMBLY


    C152878E08
  1. Disconnect the connector from the center airbag sensor assembly.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    D30-13 (CANH) - D30-22 (CANL)
    Y - W
    Ignition switch off
    54 to 69 Ω
    D30-13 (CANH) - D30-25 (E1)
    Y - B
    Ignition switch off
    200 Ω or higher
    D30-22 (CANL) - D30-25 (E1)
    W - B
    Ignition switch off
    200 Ω or higher
    D30-13 (CANH) - D47-16 (BAT)
    Y - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D30-22 (CANL) - D47-16 (BAT)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher


ECM

G035613E33

  1. Disconnect the connector from the ECM.



  2. C170023E01
  3. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    D36-33 (CANH) - D36-34 (CANL)
    R - W
    Ignition switch off
    108 to 132 Ω
    D36-33 (CANH) - B3-1 (E1)
    R - W-B
    Ignition switch off
    200 Ω or higher
    D36-34 (CANL) - B3-1 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D36-33 (CANH) - D35-3 (BATT)
    R - R
    Negative battery terminal disconnected
    6 kΩ or higher
    D36-34 (CANL) - D35-3 (BATT)
    W - R
    Negative battery terminal disconnected
    6 kΩ or higher


AIR CONDITIONING AMPLIFIER
C152868E02
  1. Disconnect the amplifier connector from air conditioning amplifier.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    D37-11 (CANH) - D37-12 (CANL)
    LG - W
    Ignition switch off
    54 to 69 Ω
    D37-11 (CANH) - D37-14 (GND)
    LG - W-B
    Ignition switch off
    200 Ω or higher
    D37-12 (CANL) - D37-14 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D37-11 (CANH) - D37-21 (B)
    LG - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D37-12 (CANL) - D37-21 (B)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher


COMBINATION METER


    C109571E20
  1. Disconnect the connector from the combination meter.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    E1-25 (CANH) - E1-26 (CANL)
    P - W
    Ignition switch off
    108 to 132 Ω
    E1-25 (CANH) - E1-20 (ES)
    P - R
    Ignition switch off
    200 Ω or higher
    E1-26 (CANL) - E1-20 (ES)
    W - R
    Ignition switch off
    200 Ω or higher
    E1-25 (CANH) - E1-21 (B)
    P - SB
    Negative battery terminal disconnected
    6 kΩ or higher
    E1-26 (CANL) - E1-21 (B)
    W - SB
    Negative battery terminal disconnected
    6 kΩ or higher


CERTIFICATION ECU (w/ Smart Key System)


    C152870E04
  1. Disconnect the connector from the certification ECU.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    D40-27 (CANH) - D40-28 (CANL)
    GR - W
    Ignition switch off
    54 to 69 Ω
    D40-27 (CANH) - D40-17 (E)
    GR - B
    Ignition switch off
    200 Ω or higher
    D40-28 (CANL) - D40-17 (E)
    W - B
    Ignition switch off
    200 Ω or higher
    D40-27 (CANH) - D40-1 (+B)
    GR - B
    Negative battery terminal disconnected
    6 kΩ or higher
    D40-28 (CANL) - D40-1 (+B)
    W - B
    Negative battery terminal disconnected
    6 kΩ or higher


MAIN BODY ECU
  1. Disconnect the connector from the main body ECU.



  2. C195603E01
  3. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    D9-5 (CANH) - D9-6 (CANL)
    GR - W
    Ignition switch off
    54 to 69 Ω
    D9-5 (CANH) - D47-4 (CG)
    GR - B
    Ignition switch off
    200 Ω or higher
    D9-6 (CANL) - D47-4 (CG)
    W - B
    Ignition switch off
    200 Ω or higher
    D9-6 (CANH) - D47-16 (BAT)
    GR - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D9-6 (CANL) - D47-16 (BAT)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D9-16 (CANP) - D9-15 (CANN)
    Y - W
    Ignition switch off
    108 to 132 Ω
    D9-16 (CANP) - D47-4 (CG)
    Y - B
    Ignition switch off
    200 Ω or higher
    D9-15 (CANN) - D47-4 (CG)
    W - B
    Ignition switch off
    200 Ω or higher
    D9-16 (CANP) - D47-16 (BAT)
    Y - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D9-15 (CANN) - D47-16 (BAT)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher


POWER STEERING ECU


    C160514E16
  1. Disconnect the power steering ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    D6-2 (CANH) - D6-8 (CANL)
    BR - W
    Ignition switch off
    54 to 69 Ω
    D6-2 (CANH) - D5-2 (PGND)
    BR - W
    Ignition switch off
    200 Ω or higher
    D6-8 (CANL) - D5-2 (PGND)
    W - W
    Ignition switch off
    200 Ω or higher
    D6-2 (CANH) - D5-1 (PIG)
    BR - B
    Negative battery terminal disconnected
    6 kΩ or higher
    D6-8 (CANL) - D5-1 (PIG)
    W - B
    Negative battery terminal disconnected
    6 kΩ or higher


BACK DOOR ECU


    C169769E01
  1. Disconnect the back door ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    O15-6 (MPX1) - O15-5 (MPX2)
    B - W
    Ignition switch off
    54 to 69 Ω
    O15-6 (MPX1) - O15-11 (GND)
    B - W-B
    Ignition switch off
    200 Ω or higher
    O15-5 (MPX2) - O15-11 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    O15-6 (MPX1) - O15-12 (B)
    B - B
    Negative battery terminal disconnected
    6 kΩ or higher
    O15-5 (MPX2) - O15-12 (B)
    W - B
    Negative battery terminal disconnected
    6 kΩ or higher


ACCESSORY GATEWAY


    C169659E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    D50-1 (CAN+) - D50-2 (CAN-)
    BR - W
    Ignition switch off
    54 to 69 Ω
    D50-1 (CAN+) - D47-4 (CG)
    BR - B
    Ignition switch off
    200 Ω or higher
    D50-2 (CAN-) - D47-4 (CG)
    W - B
    Ignition switch off
    200 Ω or higher
    D50-1 (CAN+) - D47-16 (BAT)
    BR - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D50-2 (CAN-) - D47-16 (BAT)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher