Home › TRANSMISSION · U151F AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE UNIT

AUTOMATIC TRANSAXLE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C099458
  1. Remove the nut, washer and control shaft lever.



    C161138
  1. Using a screwdriver, pry up the lock plate.



    G025453
  1. Remove the lock nut and the lock plate.



    C099454
  1. Remove the 2 bolts and pull out the park/neutral position switch.



2. REMOVE BREATHER PLUG HOSE
  1. Remove the breather plug hose from the transaxle case.



3. REMOVE OIL COOLER TUBE UNION (INLET OIL COOLER UNION)


    C083143E04
  1. Remove the union.

  1. Remove the O-ring from the union.



4. REMOVE OIL COOLER TUBE UNION (OUTLET OIL COOLER UNION)


    C083144E05
  1. Remove the union.

  1. Remove the O-ring from the union.



5. REMOVE SPEED SENSOR


    C161143E01
  1. Remove the 2 bolts and the 2 speed sensors from the transaxle assembly.



6. REMOVE NO. 1 TRANSAXLE CASE PLUG


    D026716
  1. Remove the 4 No. 1 transaxle case plugs from the transaxle case.

  1. Remove the 4 O-rings from the 4 No. 1 transaxle case plugs.



7. SUPPORT AUTOMATIC TRANSAXLE ASSEMBLY


    D009176
  1. Support the transaxle assembly on wooden blocks.



8. REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


    C091925
  1. Remove the 18 bolts, oil pan, and gasket.



    D030865E03
  1. Remove the 2 magnets from the oil pan.



9. INSPECT TRANSMISSION OIL CLEANER MAGNET


    AT00103E03
  1. Remove the magnets and use them to collect any steel chips. Examine the chips and particles in the pan and on the magnet to determine what type of wear has occurred in the transaxle:

    Result:
    Steel (magnetic):
    Wear of the bearing, gear, and plate
    Brass (non-magnetic):
    Wear of the bushing



10. DISCONNECT TRANSMISSION WIRE


    C091927E02
  1. Remove the 7 connectors from the shift solenoid valves.

  1. Remove the bolt, lock plate, and temperature sensor.



11. REMOVE TRANSMISSION WIRE


    D003547E05
  1. Remove the bolt and transmission wire from the transaxle case.



12. REMOVE VALVE BODY OIL STRAINER ASSEMBLY


    C091931
  1. Remove the 3 bolts and oil strainer.



    C091932E03
  1. Remove the O-ring from the oil strainer.



13. REMOVE TRANSMISSION VALVE BODY ASSEMBLY


    C091933
  1. Support the valve body assembly and remove the 17 bolts and valve body assembly.



14. REMOVE NO. 1 GOVERNOR APPLY GASKET


    C083127
  1. Remove the No. 1 governor apply gasket from the transaxle case.



15. REMOVE TRANSAXLE CASE 2ND BRAKE GASKET


    C083128
  1. Remove the transaxle case 2nd brake gasket from the transaxle case.



16. REMOVE BRAKE DRUM GASKET


    C083129
  1. Remove the brake drum gasket from the transaxle case.



17. REMOVE CHECK BALL BODY


    D003554E01
  1. Remove the check ball body and spring from the transaxle case.



18. REMOVE C-3 ACCUMULATOR PISTON


    D003555
  1. Remove the spring from the C-3 accumulator piston.



    D003556E01
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-3 accumulator piston.

    NOTICE:
    1. Applying compressed air may cause the piston to jump-out. When removing the piston, hold it using a shop rag or a piece of cloth.
    2. Take care not to splash ATF when applying compressed air.



    D003902E05
  1. Remove the O-ring from the C-3 accumulator piston.



19. REMOVE REVERSE CLUTCH ACCUMULATOR PISTON


    D026401
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the reverse accumulator piston and spring.

    NOTICE:
    1. Applying compressed air may cause the piston to jump-out. When removing the piston, hold it using a shop rag or a piece of cloth.
    2. Take care not to splash ATF when applying compressed air.



    D026402E08
  1. Remove the 2 O-rings from the reverse clutch accumulator piston.



20. REMOVE B-3 ACCUMULATOR PISTON


    D003558E01
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the B-3 accumulator piston and 2 springs.

    NOTICE:
    1. Applying compressed air may cause the piston to jump-out. When removing the piston, hold it using a shop rag or a piece of cloth.
    2. Take care not to splash ATF when applying compressed air.



    D003904E10
  1. Remove the O-ring from the B-3 accumulator piston.



21. REMOVE MANUAL VALVE LEVER SHAFT RETAINER SPRING


    D003559
  1. Using needle-nose pliers, remove the manual valve lever shaft retainer spring.



22. REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY


    D003560
  1. Remove the 2 bolts, the manual detent spring sub-assembly and cover.



23. REMOVE PARKING LOCK PAWL BRACKET


    C056727
  1. Remove the 2 bolts and parking lock pawl bracket.



24. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY


    D003563
  1. Using a chisel and hammer, cut off and remove the spacer.



    D003564
  1. Using a pin punch (φ35 mm) and hammer, drive out the pin.

    HINT:
    Slowly drive out the pin so that it will not fall into the transaxle case.



    D003565
  1. Remove the manual valve lever shaft and manual valve lever.



25. REMOVE PARKING LOCK ROD SUB-ASSEMBLY


    D026382E01
  1. Remove the parking lock rod from the manual valve lever.



26. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL


    D003566E01
  1. Using a screwdriver, remove the oil seal from the transaxle case.

    NOTICE:
    Do not apply excessive force when removing the oil seal.



27. SUPPORT AUTOMATIC TRANSAXLE ASSEMBLY
  1. Support the transaxle case with the oil pump side facing up.



28. INSPECT INPUT SHAFT END PLAY


    D008091
  1. Using a dial indicator, measure the input shaft end play.

    End play:
    0.262 to 1.244 mm (0.0103 to 0.0490 in.)

    HINT:
    If the result is not as specified, replace the input shaft or thrust needle roller bearing.



29. REMOVE TRANSAXLE HOUSING


    D003568
  1. Remove the 16 bolts.

  1. Tap on the circumference of the transaxle housing with a plastic hammer to remove the transaxle housing from the transaxle case.

    NOTICE:
    The differential may be accidentally removed when the transaxle housing is removed.



30. REMOVE OIL PUMP ASSEMBLY


    D003569E09
  1. Remove the 7 bolts and oil pump from the transaxle case.



31. REMOVE THRUST NEEDLE ROLLER BEARING


    D101207E01
  1. Remove the thrust needle roller bearing from the underdrive planetary gear assembly.



32. REMOVE NO. 2 THRUST BEARING UNDERDRIVE RACE


    D101208E01
  1. Remove the No. 2 thrust bearing underdrive race from the underdrive planetary gear assembly.



33. REMOVE DIFFERENTIAL GEAR ASSEMBLY


    D026450E11
  1. Remove the differential gear assembly from the transaxle case.



34. REMOVE OVERDRIVE BRAKE GASKET


    D003573
  1. Remove the 2 overdrive brake gaskets from the transaxle case.



35. REMOVE FORWARD CLUTCH ASSEMBLY


    D003574E05
  1. Remove the forward clutch assembly from the transaxle case.



    D003906E01
  1. Remove the thrust needle roller bearing from the forward clutch.



36. REMOVE MULTIPLE DISC CLUTCH HUB


    D026787E11
  1. Remove the 2 thrust needle roller bearings, multiple disc clutch hub, and No. 1 thrust bearing race.



37. INSPECT MULTIPLE DISC CLUTCH HUB


    D003829E06
  1. Using a dial indicator, measure the inside diameter of the forward clutch hub bushing.

    Standard inside diameter:
    23.025 to 23.046 mm (0.9065 to 0.9073 in.)

    Maximum inside diameter:
    23.09 mm (0.9091 in.)

    NOTICE:
    1. Check the contact surface of the bushing in the direct clutch shaft. If any scratch or discoloration is found, replace the direct clutch sub-assembly with a new one.

    If the inside diameter is greater than the maximum, replace the forward clutch hub with a new one.



38. REMOVE UNDERDRIVE PLANETARY GEAR ASSEMBLY


    D003576E05
  1. Remove the bolt and pawl shaft clamp.



    D009652
  1. Remove the parking lock pawl shaft.



    D009689
  1. Push the parking lock pawl.

    HINT:
    Failure to do this will cause interference when the underdrive planetary gear is removed.



    D003579E06
  1. Remove the underdrive planetary gear assembly from the transaxle case.

    NOTICE:
    Be careful so that the underdrive planetary gear assembly will not fall off.



39. REMOVE PARKING LOCK PAWL


    D026386
  1. Remove the spring, pawl pin, and parking lock pawl.



40. REMOVE UNDERDRIVE CLUTCH ASSEMBLY


    D003580E04
  1. Remove the underdrive clutch assembly, thrust bearing, and bearing race from the transaxle case.



41. REMOVE UNDERDRIVE ONE-WAY CLUTCH ASSEMBLY


    D003581E01
  1. Using a screwdriver, remove the snap ring from the transaxle case.

    NOTICE:
    Do not apply excessive force when removing the snap ring.



    D003627E08
  1. Remove the underdrive one-way clutch from the transaxle case.



    D003907E03
  1. Remove the outer race retainer from the one-way clutch.



42. REMOVE NO. 2 UNDERDRIVE CLUTCH DISC


    D026466E01
  1. Using a screwdriver, remove the snap ring.

    NOTICE:
    Do not apply excessive force when removing the snap ring.



    D026385E01
  1. Remove the flange, 4 discs, and 4 plates from the transaxle case.



43. INSPECT NO. 2 UNDERDRIVE CLUTCH DISC


    D009196
  1. Check if the sliding surfaces of the disc, plate, and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of the disc comes off or discolors, or if a part of the groove is worn, replace all discs.
    2. Before installing new discs, immerse them in ATF for at least 15 minutes.



44. REMOVE TRANSAXLE REAR COVER SUB-ASSEMBLY


    D026387E02
  1. Remove the 11 bolts.

  1. Tap on the circumference of the rear cover with a plastic hammer to remove the transaxle rear cover from the transaxle case.



45. REMOVE NO. 1 TRANSAXLE CASE PLUG


    D026388
  1. Remove the 4 No. 1 transaxle case plugs from the transaxle rear cover.

  1. Remove the 4 No. 1 O-rings from the 4 transaxle case plugs.



46. REMOVE REAR CLUTCH OIL SEAL RING OUTER


    D026389E01
  1. Remove the 3 rear clutch oil seal rings from the transaxle rear cover.



47. REMOVE NEEDLE ROLLER BEARING


    D026472E01
  1. Using SST, remove the needle roller bearing from the transaxle rear cover.

    SST
    09387-00041   (09387-01021, 09387-01030, 09387-01040)



48. REMOVE NO. 1 GOVERNOR APPLY GASKET


    D026390
  1. Using a screwdriver, remove the 3 apply gaskets.



49. REMOVE BRAKE APPLY TUBE


    D026391E03
  1. Remove the bolt, clamp, and brake apply tube.

  1. Remove the clutch apply tube.

  1. Remove the brake apply tube from the clamp.

    NOTICE:
    Do not bend the tubes.



50. REMOVE DIRECT CLUTCH ASSEMBLY


    D026403E07
  1. Remove the thrust bearing and the direct clutch assembly from the transaxle case.



51. REMOVE OVERDRIVE DIRECT CLUTCH HUB SUB-ASSEMBLY


    D026392E07
  1. Remove the thrust bearing race, thrust bearing, and overdrive direct clutch hub from the planetary gear assembly.



52. INSPECT OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY


    D003829E01
  1. Using a dial indicator, measure the inside diameter of the forward clutch hub bushing.

    Standard inside diameter:
    23.025 to 23.046 mm (0.9065 to 0.9073 in.)

    Maximum inside diameter:
    23.09 mm (0.9091 in.)

    NOTICE:
    1. Check the contact surface of the bushing in the direct clutch shaft. If any scratch or discoloration is found, replace the direct clutch sub-assembly with a new one.

    If the inside diameter is greater than the maximum, replace the forward clutch hub with a new one.



53. REMOVE REAR PLANETARY SUN GEAR ASSEMBLY


    D026714E07
  1. Remove the rear planetary sun gear assembly from the transaxle case.



    D026404E08
  1. Remove the thrust needle roller bearing and thrust bearing race from the rear planetary sun gear assembly.



    D026393E04
  1. Remove the No. 2 planetary carrier thrust washer from the rear planetary sun gear assembly.



54. REMOVE ONE-WAY CLUTCH ASSEMBLY


    D026598E05
  1. Remove the one-way clutch assembly and the thrust needle roller bearing from the transaxle case.



    D003909E06
  1. Remove the one-way clutch inner race from the one-way clutch assembly.



55. REMOVE ONE-WAY CLUTCH SLEEVE OUTER


    D003589E07
  1. Remove the one-way clutch sleeve outer from the transaxle case.



56. REMOVE NO. 1 PLANETARY CARRIER THRUST WASHER


    D026394E05
  1. Remove the No. 1 planetary carrier thrust washer from the planetary gear assembly.



57. REMOVE 2ND BRAKE CLUTCH DISC


    D026395E01
  1. Using a screwdriver, remove the snap ring.

  1. Remove the flange, 4 discs, and 4 plates from the transaxle case.



58. INSPECT 2ND BRAKE CLUTCH DISC


    D026717
  1. Check if the sliding surface of the disc, plate, and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of the disc comes off or discolors, or if a part of the groove is worn, replace all discs.
    2. Before installing new discs, immerse them in ATF for at least 15 minutes.



59. REMOVE 2ND BRAKE PISTON ASSEMBLY


    D008058E01
  1. Using a screwdriver, remove the snap ring.



    D026396E07
  1. Remove the 2nd brake piston assembly from the transaxle case.



60. REMOVE REAR PLANETARY GEAR ASSEMBLY


    D003616E01
  1. Using a screwdriver, remove the snap ring.



    D026591E05
  1. Remove the rear planetary gear assembly from the transaxle case.



61. REMOVE INPUT SUN GEAR


    C134855E01
  1. Remove the 2 thrust needle roller bearings, No. 2 thrust bearing race, No. 3 thrust bearing race, and the input sun gear from the transaxle case.



62. REMOVE 1ST AND REVERSE BRAKE CLUTCH DISC


    D026397
  1. Remove the flange, 6 discs, and 6 plates from the transaxle case.



63. INSPECT 1ST AND REVERSE BRAKE CLUTCH DISC


    D009189
  1. Check if the sliding surface of the disc, plate, and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of the disc comes off or discolors, or if a part of the groove is worn, replace all discs.
    2. Before installing new discs, immerse them in ATF for at least 15 minutes.



64. REMOVE FRONT PLANETARY GEAR ASSEMBLY


    D003595E01
  1. Using a chisel and hammer, unstake the lock washer.

    NOTICE:
    Push down all claws of the washer. Otherwise, SST cannot be fully pressed against the nut, and the nut cannot be loosened.



    D003596E01
  1. Using SST, remove the nut.

    SST
    09387-00030  
    09387-00080  



    D026398E01
  1. Using SST and a press, remove the front planetary gear assembly from the counter drive gear.

    SST
    09950-60010   (09951-00450)
    09950-70010   (09951-07100)



    D026763E04
  1. Remove the front planetary gear assembly from the brake hub.



65. REMOVE FRONT PLANETARY RING GEAR


    D003615E06
  1. Using a screwdriver, remove the snap ring and front planetary ring gear from the brake hub.



66. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


    D003600E01
  1. Place SST on the return spring, and compress the return spring with a press.

    SST
    09387-00070  

  1. Using a snap ring expander, remove the snap ring.

    NOTICE:
    1. Stop the press when the spring seat is lowered 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove to prevent the spring seat from being deformed.
    2. Do not expand the snap ring excessively.



67. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


    C161144E02
  1. Using vernier calipers, measure the free length of the spring together with the spring seat.

    Standard free length:
    17.61 mm (0.6933 in.)

    HINT:
    If the result is not as specified, replace the spring.



68. REMOVE 1ST AND REVERSE BRAKE PISTON


    D026405E03
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the 1st and reverse brake piston.

    NOTICE:
    1. Applying compressed air may cause the piston to jump-out. When removing the piston, hold it using a shop rag or a piece of cloth.
    2. Take care not to splash ATF when applying compressed air.



    D026713E03
  1. Remove the 2 O-rings from the 1st and reverse brake piston.



69. REMOVE COUNTER DRIVE GEAR


    C089120E01
  1. Using SST and a press, remove the counter drive gear from the transaxle case.

    SST
    09950-60010   (09951-00590)
    09950-70010   (09951-07100)



    D003602E01
  1. As shown in the illustration, tighten the 2 bolts evenly and make clearance of approx. 20.0 mm (0.787 in.) between the counter drive gear and the inner race.



    D003603E01
  1. Using SST, remove the tapered roller bearing.

    SST
    09950-60010   (09951-00590)
    09950-00020  
    09950-00030  
    09950-40011   (09957-04010)



70. REMOVE COUNTER DRIVE GEAR BEARING


    D026467E01
  1. Using a snap ring expander, remove the snap ring.



    C089121E01
  1. Using SST and a press, remove the bearing outer race.

    SST
    09950-60020   (09951-00910)



71. REMOVE NO. 2 BREATHER PLUG


72. REMOVE UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY


    D026407E01
  1. Place SST on the return spring, and compress the return spring with a press.

    SST
    09387-00020  

  1. Using a snap ring expander, remove the snap ring.

    NOTICE:
    1. Stop the press when the spring seat is lowered 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove, to prevent the spring seat from being deformed.
    2. Do not expand the snap ring excessively.



73. INSPECT UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY


    D030852E11
  1. Using vernier calipers, measure the free length of the spring together with the spring seat.

    Standard free length:
    13.24 mm (0.5213 in.)

    HINT:
    If the result is not as specified, replace the spring.



74. REMOVE UNDERDRIVE BRAKE PISTON


    D026406E01
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the underdrive brake piston.



    D003794E04
  1. Remove the 2 O-rings from the underdrive brake piston.



75. REMOVE NEEDLE ROLLER BEARING


    D003605E01
  1. Using SST, remove the needle roller bearing from the transaxle case.

    SST
    09387-00041   (09387-01010, 09387-01030, 09387-01040)



76. REMOVE UNDERDRIVE CLUTCH DRUM OIL SEAL RING


    D003914E09
  1. Remove the 2 oil seal rings from the transaxle case.



77. REMOVE NO. 1 TRANSAXLE CASE PLUG


    D026383
  1. Remove the 2 No. 1 transaxle case plugs.

  1. Remove the 2 O-rings from the 2 No. 1 transaxle case plugs.



78. REMOVE UNDERDRIVE CYLINDRICAL ROLLER BEARING


    D003606E01
  1. Using SST, remove the underdrive cylindrical roller bearing from the transaxle case.

    SST
    09514-35011  



79. REMOVE UNDERDRIVE OUTPUT SHAFT OIL SEAL RING


    D003915E10
  1. Remove the oil seal ring from the transaxle housing.



80. REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE


    D026400E08
  1. Remove the bolt, transaxle apply tube clamp and differential gear lube apply tube from the transaxle housing.

    NOTICE:
    Do not bend the tubes.