AUTOMATIC TRANSAXLE UNIT > REASSEMBLY |
| 1. BEARING POSITION |

| Mark | Front Race Diameter Inside / Outside mm (in.) | Thrust Bearing Diameter Inside / Outside mm (in.) | Rear Race Diameter Inside / Outside mm (in.) |
| A | - | 57.2 (2.252) / 84.96 (3.3449) | 56.4 (2.220) / 83.0 (3.268) |
| B | - | 37.73 (1.4854) / 58.0 (2.283) | - |
| C | - | 33.85 (1.3327) / 52.2 (2.055) | - |
| D | 24.94 (0.9820) | 23.5 (0.925) / 44.0 (1.732) | - |
| E | - | 36.3 (1.429) / 51.93 (2.0445) | 34.5 (1.358) / 48.35 (1.9035) |
| F | 34.35 (1.3526) / 56.57 (2.2271) | 32.45 (1.2776) / 56.48 (2.2236) | - |
| G | 40.15 (1.5807) / 59.25 (2.3327) | 38.65 (1.5217) / 59.79 (2.3539) | 38.65 (1.5217) / 59.25 (2.3327) |
| H | - | 53.6 (2.110) / 69.6 (2.740) | - |
| I | 33.02 (1.3000) / 45.8 (1.803) | 31.85 (1.2539) / 57.3 (2.256) | - |
| J | - | 24.79 (0.976) / 39.5 (1.555) | 23.6 (0.929) / 37.95 (1.4941) |
| K | - | 56.3 (2.217) / 75.96 (2.9905) | - |
| 2. INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE |
![]() |
Install the differential gear lube apply tube and transaxle apply tube clamp to the transaxle housing with the bolt.
| 3. INSTALL NO. 1 TRANSAXLE CASE PLUG |
![]() |
Install 2 new O-rings to the 2 No. 1 transaxle case plugs.
Install the 2 No. 1 transaxle case plugs to the transaxle rear cover.
| 4. INSTALL UNDERDRIVE OUTPUT SHAFT OIL SEAL RING |
![]() |
Coat a new oil seal ring with ATF and install it to the transaxle housing.
| 5. INSTALL UNDERDRIVE CYLINDRICAL ROLLER BEARING |
![]() |
Coat the underdrive cylindrical roller bearing with ATF.
Using SST and a press, install the underdrive cylindrical roller bearing.
| 6. INSTALL UNDERDRIVE CLUTCH DRUM OIL SEAL RING |
![]() |
Coat 2 new oil seal rings with ATF and install them to the transaxle rear cover.
| 7. INSTALL NEEDLE ROLLER BEARING |
![]() |
Wrap vinyl tape around SST 4.0 mm (0.157 in.) from the bottom of SST until the thickness of the tape is approximately 5.0 mm (0.197 in.).
Coat the needle roller bearing with ATF.
![]() |
Using SST and a press, install the needle-roller bearing to the transaxle case.
| 8. INSTALL UNDERDRIVE BRAKE PISTON |
![]() |
Coat 2 new O-rings with ATF and install them to the underdrive brake piston.
Coat the underdrive brake piston with ATF.
![]() |
Install the underdrive brake piston to the transaxle case.
| 9. INSTALL UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY |
![]() |
Place SST on the return spring and compress the return spring with a press.
Using a snap ring expander, install the snap ring to the transaxle case.
| 10. INSTALL NO. 2 BREATHER PLUG |
| 11. INSTALL COUNTER DRIVE GEAR BEARING |
![]() |
Coat the counter drive gear bearing with ATF.
Using SST and a press, install the bearing outer race.
![]() |
Using a snap ring expander, install the snap ring.
| 12. INSTALL COUNTER DRIVE GEAR |
![]() |
Coat the counter drive gear with ATF.
Using SST and a press, install the tapered roller bearing to the counter drive gear.
![]() |
Using SST and a press, install the counter drive gear and bearing to the transaxle case.
| 13. INSTALL 1ST AND REVERSE BRAKE PISTON |
![]() |
Coat 2 new O-rings with ATF.
Install the 2 O-rings to the 1st and reverse brake piston.
![]() |
Coat the 1st and reverse brake piston with ATF and install it to the transaxle case.
| 14. INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY |
![]() |
Place SST on the return spring and compress the return spring with a press.
Using a snap ring expander, install the snap ring to the transaxle case.
| 15. INSTALL FRONT PLANETARY RING GEAR |
![]() |
Using a screwdriver, install the front planetary ring gear and snap ring to the brake hub.
| 16. INSTALL FRONT PLANETARY GEAR ASSEMBLY |
![]() |
Install the front planetary gear assembly to the brake hub.
![]() |
Using SST and a press, press-fit the front planetary gear assembly.
![]() |
Install a new washer as shown in the illustration.
![]() |
Using SST, install the nut.
![]() |
Using SST and a torque wrench, measure the turning torque of the bearing while rotating SST at 60 rpm. When the measured value is not as specified, gradually tighten the nut until it reaches the specified value.
Tighten the nut gradually until the specified turning torque of the tapered roller bearing is measured.
![]() |
Using a chisel and hammer, stake the front lock washer.
| 17. INSTALL INPUT SUN GEAR |
![]() |
Coat the 2 thrust bearings with ATF.
Install the 2 thrust bearings, the 3 bearing races, and the input sun gear to the transaxle case.
| Inside | Outside | |
| Bearing Race, A | 34.5 (1.358) | 56.82 (2.2370) |
| Thrust Bearing, B | 32.4 (1.276) | 56.62 (2.2291) |
| Bearing Race, C | 40.3 (1.587) | 58.0 (2.284) |
| Thrust Bearing, D | 40.3 (1.587) | 58.1 (2.287) |
| Bearing Race, E | 38.6 (1.520) | 58.0 (2.284) |
| 18. INSTALL REAR PLANETARY GEAR ASSEMBLY |
![]() |
Install the rear planetary gear assembly to the rear planetary ring gear.
![]() |
Using a screwdriver, install the snap ring.
| 19. INSTALL 1ST AND REVERSE BRAKE CLUTCH DISC |
![]() |
Coat the 6 discs with ATF.
Install the 6 plates and 6 discs.
| 20. INSPECT PACK CLEARANCE OF FIRST AND REVERSE BRAKE |
![]() |
Using vernier calipers, measure the distance between the disc surface and the contact surface of the 2nd brake cylinder and transaxle case (Dimension A).
Select an appropriate flange so that the pack clearance will be within the specified range.
| Mark | Thickness | Mark | Thickness |
| 1 | 1.8 (0.071) | 5 | 2.2 (0.087) |
| 2 | 1.9 (0.075) | 6 | 2.3 (0.091) |
| 3 | 2.0 (0.079) | 7 | 2.4 (0.094) |
| 4 | 2.1 (0.083) | 8 | 2.5 (0.098) |
![]() |
Install the flange.
| 21. INSTALL 2ND BRAKE PISTON ASSEMBLY |
![]() |
Install the 2nd brake piston assembly to the transaxle case.
![]() |
Install the snap ring and measure the inside diameter.
| 22. INSTALL ONE-WAY CLUTCH SLEEVE OUTER |
![]() |
Install the one-way clutch sleeve outer to the 2nd brake cylinder assembly.
| 23. INSTALL ONE-WAY CLUTCH ASSEMBLY |
![]() |
Install the one-way clutch inner race to the one-way clutch.
![]() |
Check the rotating direction of one-way clutch for the lock or free operation as shown in the illustration.
![]() |
Install the one-way clutch and thrust needle roller bearing to the one-way clutch sleeve outer.
| Inside | Outside | |
| Bearing | 53.6 (2.110) | 69.4 (2.732) |
| 24. INSTALL NO. 1 PLANETARY CARRIER THRUST WASHER |
![]() |
Coat the No. 1 planetary carrier thrust washer with yellow petrolatum, and install the washer onto the planetary sun gear assembly.
| 25. INSTALL REAR PLANETARY SUN GEAR ASSEMBLY |
![]() |
Coat the No. 2 planetary carrier thrust washer with yellow petrolatum, and install the washer onto the rear planetary sun gear.
![]() |
Coat the bearing with yellow petrolatum, and install the bearing onto the rear planetary sun gear.
| Inside | Outside | |
| Race, A | 33.0 (1.299) | 45.4 (1.787) |
| Bearing, B | 31.85 (1.254) | 45.2 (1.78) |
![]() |
Install the rear planetary sun gear assembly to the rear planetary gear.
| 26. INSTALL 2ND BRAKE CLUTCH DISC |
![]() |
Coat the 4 discs with ATF.
Install the 4 discs and 4 plates to the transaxle case.
Temporarily install the snap ring.
| 27. INSPECT PACK CLEARANCE OF 2ND BRAKE |
![]() |
Using vernier calipers, measure the distance between the disc surface and snap ring surface (Dimension B).
Select an appropriate flange so that the pack clearance will be within the specified range.
| Mark | Thickness | Mark | Thickness |
| 1 | 3.0 (0.118) | 5 | 3.4 (0.134) |
| 2 | 3.1 (0.122) | 6 | 3.5 (0.138) |
| 3 | 3.2 (0.126) | 7 | 3.6 (0.142) |
| 4 | 3.3 (0.130) | 8 | - |
![]() |
Temporarily remove the snap ring, attach the selected flange, and reinstall the snap ring.
| 28. INSTALL OVERDRIVE DIRECT CLUTCH HUB SUB-ASSEMBLY |
![]() |
Install the direct clutch hub to the planetary gear assembly.
Coat the thrust bearing with ATF.
Install the bearing race and the thrust bearing to the direct clutch hub.
| Inside | Outside | |
| Bearing, A | 24.7 (0.972) | 39.5 (1.555) |
| Race, B | 23.6 (0.929) | 38.0 (1.496) |
| 29. INSTALL DIRECT CLUTCH ASSEMBLY |
![]() |
Coat the thrust bearing with ATF.
Install the direct clutch assembly and thrust bearing to the rear planetary sun gear assembly.
![]() |
Clean the connecting part of the transaxle case and the rear cover.
As shown in the illustration, place a straightedge on the direct clutch drum and measure the distance between the transaxle case and the straightedge using vernier calipers (Dimension C).
![]() |
Using vernier calipers and a straightedge, measure the dimension shown in the illustration.
Calculate the end play using the following formula. Select a thrust bearing which satisfies the end play and install the selected bearing.
| Thickness | Inside | Outside |
| 3.6 (0.1417) | 56.3 (2.217) | 75.7 (2.980) |
| 3.8 (0.1496) | 56.3 (2.217) | 75.7 (2.980) |
| 30. INSTALL NO. 1 GOVERNOR APPLY GASKET |
![]() |
Install 3 new No. 1 governor apply gaskets to the transaxle case.
| 31. INSTALL BRAKE APPLY TUBE |
![]() |
Install the clamp to the brake apply tube.
Install the clutch apply tube.
![]() |
Install the brake apply tube and a bolt to the transaxle case.
| 32. INSTALL NEEDLE ROLLER BEARING |
![]() |
Using SST and a press, press the needle roller bearing into the transaxle rear cover.
Coat a needle roller bearing with ATF.
| 33. INSTALL REAR CLUTCH OIL SEAL RING OUTER |
![]() |
Coat 3 new rear clutch oil seal rings with ATF, and install them to the transaxle rear cover.
| 34. INSTALL NO. 1 TRANSAXLE CASE PLUG |
![]() |
Coat 4 new O-rings with ATF.
Install the 4 O-rings to the 4 No. 1 transaxle case plugs.
Install the 4 No. 1 transaxle case plugs to the transaxle rear cover.
| 35. INSTALL TRANSAXLE REAR COVER SUB-ASSEMBLY |
![]() |
Remove any packing material and be careful not to spill oil on the contact surfaces of the transaxle rear cover or the transaxle case.
Apply seal packing to the cover.
![]() |
Apply adhesive to the "A" bolt threads.
Install the 11 bolts.
| 36. INSTALL NO. 2 UNDERDRIVE CLUTCH DISC |
![]() |
Coat the 4 discs with ATF.
Install the 4 discs, 4 plates, and flange to the transaxle case.
![]() |
Using a screwdriver, install the snap ring.
| 37. INSPECT PACK CLEARANCE OF UNDERDRIVE BRAKE |
![]() |
Using a dial indicator, measure the underdrive brake pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).
| Mark | Thickness | Mark | Thickness |
| 1 | 3.0 (0.118) | 4 | 3.1 (0.122) |
| 2 | 3.2 (0.126) | 5 | 3.3 (0.130) |
| 3 | 3.4 (0.134) | - | - |
Temporarily remove the snap ring and attach it to the flange.
Reinstall the snap ring.
| 38. INSPECT UNDERDRIVE ONE-WAY CLUTCH ASSEMBLY |
![]() |
Install the underdrive clutch assembly to the one-way clutch.
Rotate the underdrive clutch assembly to check the rotating direction for the lock or free operation.
| 39. INSTALL UNDERDRIVE ONE-WAY CLUTCH ASSEMBLY |
![]() |
Install the outer race retainer to the one-way clutch.
![]() |
Install the one-way clutch to the transaxle case.
![]() |
Using a screwdriver, install the snap ring to the transaxle case.
| 40. INSTALL UNDERDRIVE CLUTCH ASSEMBLY |
![]() |
Coat the bearing and bearing race with petroleum jelly, and install them onto the underdrive clutch.
| Inside | Outside | |
| Bearing | 37.73 (1.4854) | 58.0 (2.2835) |
| Race | 29.9 (1.1772) | 55.5 (2.185) |
Install the underdrive clutch assembly to the transaxle case.
| 41. INSTALL PARKING LOCK PAWL |
![]() |
Install the pawl pin and spring to the parking lock pawl.
![]() |
Temporarily install the parking lock pawl, shaft, and spring to the transaxle case as shown in the illustration.
| 42. INSTALL UNDERDRIVE PLANETARY GEAR ASSEMBLY |
![]() |
Install the underdrive planetary gear assembly to the transaxle case.
![]() |
Install the parking lock pawl shaft.
![]() |
Install the pawl shaft clamp with the bolt.
![]() |
Using a straightedge and vernier calipers as shown in the illustration, measure the gap between the top of the differential drive pinion in the underdrive planetary gear and the contact surface of the transaxle case and housing (Dimension E).
![]() |
As shown in the illustration, measure the 2 places of the transaxle housing, and calculate dimension F using the formula below.
| 43. INSTALL MULTIPLE DISC CLUTCH HUB |
![]() |
Install the No. 1 thrust bearing race to the transaxle case while checking its direction.
| Inside | Outside | |
| Bearing race | 39.5 (1.555) | 45.8 (1.803) |
![]() |
Coat the thrust needle roller bearing and race with yellow petrolatum, and install them onto the multiple disc clutch hub.
| Inside | Outside | |
| Thrust Bearing | 36.4 (1.433) | 52.2 (2.055) |
Coat the needle roller bearing with ATF.
![]() |
Install the needle roller bearing to the multiple clutch hub.
| Inside | Outside | |
| Bearing | 23.6 (0.929) | 44 (1.732) |
Install the multiple clutch hub to the transaxle case.
| 44. INSTALL FORWARD CLUTCH ASSEMBLY |
![]() |
Coat the thrust needle roller bearing with ATF.
Install the thrust needle roller bearing to the forward clutch.
| Inside | Outside | |
| Thrust Bearing | 33.58 (1.3220) | 51.9 (2.043) |
![]() |
Install the forward clutch to the forward clutch assembly.
| 45. INSTALL OVERDRIVE BRAKE GASKET |
![]() |
Install 2 new overdrive brake gaskets.
| 46. INSTALL DIFFERENTIAL GEAR ASSEMBLY |
![]() |
Install the differential gear assembly to the transaxle case.
| 47. INSTALL NO. 2 THRUST BEARING UNDERDRIVE RACE |
![]() |
Install the No. 2 thrust bearing underdrive race to the underdrive planetary gear assembly.
| 48. INSTALL THRUST NEEDLE ROLLER BEARING |
![]() |
Coat the thrust needle roller bearing with ATF.
Calculate the end play using the following formula and values of dimension E and F that are measured when installing the cylindrical roller bearing and underdrive planetary gear. Select an appropriate No. 2 underdrive planetary gear thrust bearing race which satisfies the specified end play, and install the selected bearing race.
| F - E | Thickness |
| Less than 7.72 (0.3039) | 3.5 (0.138) |
| 7.72 (0.3039) | 3.8 (0.150) |
| Inside | Outside | |
| Bearing | 57.2 (2.252) | 84.96 (3.345) |
| Bearing race | 56.4 (2.22) | 83 (3.268) |
| 49. INSTALL OIL PUMP ASSEMBLY |
![]() |
Install the oil pump to the transaxle case with the 7 bolts.
![]() |
Coat the O-ring of the oil pump with ATF.
| 50. INSTALL TRANSAXLE HOUSING |
![]() |
Remove any packing material and be careful not to spill oil on the contact surface of the transaxle case or transaxle housing.
Apply seal packing to the transaxle case.
![]() |
Install the transaxle housing and 16 bolts to the transaxle case.
| 51. INSPECT INPUT SHAFT END PLAY |
![]() |
Using a dial indicator, measure the input shaft end play.
| 52. SUPPORT AUTOMATIC TRANSAXLE ASSEMBLY |
![]() |
Support the transaxle assembly on wooden blocks.
| 53. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL |
![]() |
Coat a new oil seal with MP grease.
Install the oil seal to the transaxle case.
| 54. INSTALL PARKING LOCK ROD SUB-ASSEMBLY |
![]() |
Install the parking lock rod to the manual valve lever.
| 55. INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY |
![]() |
Install a new spacer and manual valve lever shaft to the transaxle case.
![]() |
Using a pin punch and hammer, drive in a new pin.
![]() |
Turn the spacer and the lever shaft to align the small hole for locating the staking position in the spacer with the staking position mark on the lever shaft.
Using a pin punch, stake the spacer through the small hole.
Check that the spacer does not turn.
| 56. INSTALL MANUAL VALVE LEVER SHAFT RETAINER SPRING |
![]() |
Using needle-nose pliers, install the retainer spring.
| 57. INSTALL PARKING LOCK PAWL BRACKET |
![]() |
Install the parking lock pawl bracket with the 2 bolts.
| 58. INSTALL MANUAL DETENT SPRING SUB-ASSEMBLY |
![]() |
Install the manual detent spring sub-assembly with the 2 bolts.
| 59. INSTALL B-3 ACCUMULATOR PISTON |
![]() |
Coat a new O-ring with ATF and install it to the B-3 accumulator piston.
![]() |
Coat the piston with ATF and install it to the transaxle case.
| Free length Outer diameter mm (in.) | Color |
| Inner 62.00 (2.4409) / 15.50 (0.610) | Purple |
| Outer 74.23 (2.9224) / 21.70 (0.854) | Purple |
| 60. INSTALL REVERSE CLUTCH ACCUMULATOR PISTON |
![]() |
Coat 2 new O-rings with ATF and install them to the reverse accumulator piston.
![]() |
Coat the piston with ATF and install it to the transaxle case.
| Free length Outer diameter mm (in.) | Color |
| 60.96 (2.3999) / 14.10 (0.555) | Yellow |
| 61. INSTALL C-3 ACCUMULATOR PISTON |
![]() |
Coat a new O-ring with ATF and install it to the C-3 accumulator piston.
![]() |
Coat the piston with ATF and install it to the transaxle case.
| Free length Outer diameter mm (in.) | Color |
| 72.20 (2.8425) / 19.0 (0.748) | Colorless |
![]() |
Install the spring to the C-3 accumulator piston.
| 62. INSTALL CHECK BALL BODY |
![]() |
Coat the check ball body with ATF.
Install the check ball body and spring.
| 63. INSTALL BRAKE DRUM GASKET |
![]() |
Coat a new brake drum gasket with ATF and install it to the transaxle case.
| 64. INSTALL TRANSAXLE CASE 2ND BRAKE GASKET |
![]() |
Coat a new transaxle case 2nd brake gasket with ATF and install it to the transaxle case.
| 65. INSTALL NO. 1 GOVERNOR APPLY GASKET |
![]() |
Coat a new No. 1 governor apply gasket with ATF and install it to the transaxle case.
| 66. INSTALL TRANSMISSION WIRE |
![]() |
Coat a new O-ring with ATF and install it to the transmission wire.
![]() |
Install the bolt that retains the transmission wire.
| 67. CONNECT TRANSMISSION WIRE |
![]() |
Coat an O-ring of the ATF temperature sensor with ATF.
Install the ATF temperature sensor with the lock plate and bolt.
Connect the 7 solenoid connectors.
| 68. INSTALL TRANSMISSION VALVE BODY ASSEMBLY |
![]() |
While positioning the manual valve lever position, install the valve body to the transaxle case with the 17 bolts.
| 69. INSTALL VALVE BODY OIL STRAINER ASSEMBLY |
![]() |
Coat a new O-ring with ATF and install it to the oil strainer.
![]() |
Install the oil strainer and 3 bolts to the valve body.
| 70. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY |
![]() |
Install the 2 magnets to the oil pan.
Apply adhesive to 18 new bolts.
![]() |
Install the oil pan and new oil pan gasket to the transaxle case with the 18 bolts.
| 71. INSTALL NO. 1 TRANSAXLE CASE PLUG |
![]() |
Coat 4 new O-rings with ATF, and install them to the 4 No. 1 transaxle case plugs.
Install the 4 No. 1 transaxle case plugs to the transaxle case.
| 72. INSTALL SPEED SENSOR |
![]() |
Coat 2 new O-rings with ATF and install them to the 2 sensors.
Install the 2 sensors to the transaxle case with the 2 bolts.
| 73. INSTALL OIL COOLER TUBE UNION (OUTLET OIL COOLER UNION) |
![]() |
Coat a new O-ring with ATF and install it to the elbow.
Install the elbow to the transaxle case.
| 74. INSTALL OIL COOLER TUBE UNION (INLET OIL COOLER UNION) |
![]() |
Coat a new O-ring with ATF and install it to the union.
Install the union to the transaxle case.
| 75. INSTALL BREATHER PLUG HOSE |
Install the breather plug hose to the transaxle case firmly.
| 76. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Install the park/neutral position switch to the manual valve shaft.
Temporarily install the 2 bolts.
![]() |
Install a new lock plate and tighten the nut.
Temporarily install the control shaft lever.
![]() |
Turn the lever counterclockwise until it stops and then turn it clockwise 2 notches.
Remove the control shaft lever.
![]() |
Align the groove with the neutral basic line.
Hold the switch in position and tighten the 2 bolts.
![]() |
Using a screwdriver, bend the tabs of the lock plate.
![]() |
Install the control shaft lever, washer and nut.
| 77. INSTALL SPEEDOMETER DRIVEN HOLE (ATM) COVER SUB-ASSEMBLY |
Coat a new O-ring with ATF and install it to the speedometer driven hole cover.
Install the bolt and speedometer driven hole cover sub-assembly to the transaxle assembly.