Home › BODY ELECTRICAL › DOOR LOCK › KEY REMINDER WARNING SYSTEM

KEY REMINDER WARNING SYSTEM > Key Reminder Buzzer does not Sound

for Preparation Click here


DESCRIPTION

The key reminder warning buzzer sounds when the driver side door is opened while the ignition switch is in the LOCK or ACC positions. The key reminder warning buzzer is activated when the main body ECU sends a key switch signal and driver side courtesy switch signal to the combination meter.

HINT:
Since the key reminder warning system has functions that use CAN communication, first confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with the "HOW TO PROCEED WITH TROUBLESHOOTING" procedures. Then, conduct the following inspection procedure.


WIRING DIAGRAM


B172183E01


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (FRONT DOOR COURTESY LIGHT SWITCH)
  1. Check the Data List for proper functioning of the front door courtesy light switch LH.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door Courtesy SW
    Front door courtesy light switch LH signal / ON or OFF
    ON: Driver side door is open
    OFF: Driver side door is closed
    -

    OK:
    ON (driver door is open) appears on the screen.



NG
Go to step 5
OK


2.READ VALUE USING TECHSTREAM (UNLOCK WARNING SWITCH)
  1. Check the Data List for proper functioning of the unlock warning switch.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Key Unlock Warning SW
    Unlock warning switch signal / ON or OFF
    ON: Key is in ignition key cylinder
    OFF: No key is in ignition key cylinder
    -

    OK:
    ON (Key is in ignition key cylinder) appears on the screen.



NG
Go to step 3
OK

REPLACE COMBINATION METER ASSEMBLY 

3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY


    B159681E06
  1. Remove the unlock warning switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch free (Key removed)
    10 kΩ or higher
    1 - 2
    Switch pushed (Key set)
    Below 1 Ω



NG
REPLACE UNLOCK WARNING SWITCH ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - MAIN BODY ECU)


    B175265E04
  1. Disconnect the D19 unlock warning switch assembly and D10 main body ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D19-1 - D10-5 (KSW)
    Always
    Below 1 Ω
    D19-1 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU) 

5.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (for Driver Side)


    B111600E09
  1. Remove the driver's side front door courtesy light switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - Switch body
    Courtesy switch pushed (Door closed)
    10 kΩ or higher
    Courtesy switch free (Door open)
    Below 1 Ω



NG
REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (for Driver Side) (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH - MAIN BODY ECU)


    B175262E06
  1. Disconnect the O2 front door courtesy switch assembly and D8 main body ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O2-1 - D8-24 (DCTY)
    Always
    Below 1 Ω
    O2-1 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)