DTC B1771 Passenger Side Buckle Switch Circuit Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1771 |
|
|

| 1.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery.
Check that the connectors are properly connected to the occupant classification ECU and the front seat inner belt assembly RH.
Disconnect the connectors from the occupant classification ECU and the front seat inner belt assembly RH.
Check that the terminals of connectors are not damaged.
|
| ||||
| OK | |
| 2.CHECK FRONT SEAT WIRE RH (SHORT TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| a3-9 (BSW) - Body ground | Ignition switch on (IG) | Below 1 V |
| a3-5 (BGND) - Body ground | Ignition switch on (IG) | Below 1 V |
|
| ||||
| OK | |
| 3.CHECK FRONT SEAT WIRE RH (OPEN) |
Turn the ignition switch off.

Disconnect the negative (-) terminal cable from the battery.
Using SST, connect terminals 2 and 1 of connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| a3-9 (BSW) - a3-5 (BGND) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 4.CHECK FRONT SEAT WIRE RH (SHORT) |
![]() |
Disconnect SST from connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| a3-9 (BSW) - a3-5 (BGND) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 5.CHECK FRONT SEAT WIRE RH (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| a3-9 (BSW) - Body ground | Always | 1 MΩ or higher |
| a3-5 (BGND) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 6.CHECK DTC |
Connect the connectors to the occupant classification ECU and the front seat inner belt assembly RH.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Clear the DTCs stored in the occupant classification ECU (Click here).
Clear the DTCs stored in the center airbag sensor assembly (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG).
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 7.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery.
Replace the front seat inner belt assembly RH (Click here).
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Clear the DTCs stored in the occupant classification ECU (Click here).
Clear the DTCs stored in the center airbag sensor assembly (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG).
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 8.REPLACE OCCUPANT CLASSIFICATION ECU |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery.
Replace the occupant classification ECU (Click here).
| NEXT | |
| 9.PERFORM ZERO POINT CALIBRATION |
Connect the negative (-) terminal cable to the battery.
Connect Techstream to the DLC3.
Turn the ignition switch on (IG).
Using Techstream, perform "zero point calibration" (Click here).
| NEXT | |
| 10.PERFORM SENSITIVITY CHECK |
Using Techstream, perform "sensitivity check" (Click here).
| NEXT | ||
| ||