Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1785    Front Occupant Classification Sensor LH Collision Detection

for Preparation Click here


DESCRIPTION

DTC B1785 is output when the occupant classification ECU receives a collision detection signal sent by the front occupant classification sensor LH if an accident occurs.
DTC B1785 is also output when the front seat assembly RH is subjected to a strong impact, even if an actual accident does not occur.
However, when the occupant classification ECU outputs a collision detection signal, even if the vehicle is not in a collision, DTC B1785 can be cleared by "zero point calibration" and "sensitivity check".
Therefore, if DTC B1785 is output, first perform "zero point calibration" and "sensitivity check".

DTC No.
DTC Detection Condition
Trouble Area
B1785
  1. Front seat assembly RH malfunction
  2. Occupant classification ECU malfunction
  3. Front occupant classification sensor LH sensed large load
  1. Front seat assembly RH (Front occupant classification sensor LH)
  2. Occupant classification ECU

HINT:
When DTC B1650/32 is detected as a result of troubleshooting for the AIRBAG SYSTEM, check the DTCs stored in the occupant classification ECU. When DTC B1785 is output, perform troubleshooting for the DTC.


WIRING DIAGRAM


C170432E04


INSPECTION PROCEDURE

1.PERFORM ZERO POINT CALIBRATION
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Using Techstream, perform "zero point calibration" (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.



NG
Go to step 4
OK


2.PERFORM SENSITIVITY CHECK
  1. Using Techstream, perform "sensitivity check" (Click here).

    Standard:
    27 to 33 kg (59.52 to 72.75 lb)



NG
Go to step 4
OK


3.CHECK DTC
  1. Turn the ignition switch on (IG).

  1. Clear the DTCs stored in the occupant classification ECU (Click here).

  1. Clear the DTCs stored in the center airbag sensor assembly (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG).

  1. Check for DTCs (Click here).

    OK:
    DTC B1785 is not output.

    HINT:
    Codes other than DTC B1785 may be output at this time, but they are not related to this check.



NG
Go to step 4
OK

END 

4.REPLACE FRONT SEAT ASSEMBLY RH
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery.

  1. Replace the front seat assembly RH (Click here for power seat or Click here for manual seat).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


5.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Using Techstream, perform "zero point calibration" (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.



NG
Go to step 8
OK


6.PERFORM SENSITIVITY CHECK
  1. Using Techstream, perform "sensitivity check" (Click here).

    Standard:
    27 to 33 kg (59.52 to 72.75 lb)



NG
Go to step 8
OK


7.CHECK DTC
  1. Turn the ignition switch on (IG).

  1. Clear the DTCs stored in the occupant classification ECU (Click here).

  1. Clear the DTCs stored in the center airbag sensor assembly (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG).

  1. Check for DTCs (Click here).

    OK:
    DTC B1785 is not output.

    HINT:
    Codes other than DTC B1785 may be output at this time, but they are not related to this check.



NG
Go to step 8
OK

END 

8.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery.

  1. Replace the occupant classification ECU (Click here).


NEXT


9.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Using Techstream, perform "zero point calibration" (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.


NEXT


10.PERFORM SENSITIVITY CHECK
  1. Using Techstream, perform "sensitivity check" (Click here).

    Standard:
    27 to 33 kg (59.52 to 72.75 lb)


NEXT

END