Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1790    Center Airbag Sensor Assembly Communication Circuit Malfunction

for Preparation Click here


DESCRIPTION

The center airbag sensor assembly communication circuit consists of the occupant classification ECU and the center airbag sensor assembly.
DTC B1790 is recorded when a malfunction is detected in the center airbag sensor assembly communication circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1790
  1. The occupant classification ECU receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the center airbag sensor assembly communication circuit for 2 seconds.
  2. Center airbag sensor assembly malfunction
  3. Occupant classification ECU malfunction
  1. Occupant classification ECU
  2. Center airbag sensor assembly
  3. Floor wire No. 2
  4. Front seat wire RH

HINT:
When DTC B1650/32 is detected as a result of troubleshooting for the AIRBAG SYSTEM, check the DTCs stored in the occupant classification ECU. When DTC B1790 is output, perform troubleshooting for the DTC.


WIRING DIAGRAM


C167958E02


INSPECTION PROCEDURE

HINT:
  1. If troubleshooting (wire harness inspection) is difficult to perform, remove the front passenger seat installation bolts to see under the seat cushion.
  2. In the above case, hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.

1.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the occupant classification ECU.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly and the occupant classification ECU.

  1. Check that the terminals of connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


2.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT TO B+)


    C169178E01
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    a3-8 (FSR+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    a3-4 (FSR-) - Body ground
    Ignition switch on (IG)
    Below 1 V



NG
Go to step 11
OK


3.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (OPEN)


  1. Turn the ignition switch off.


    C169179E01

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using SST, connect terminals 16 (FSP+) and 24 (FSP-) of connector B.

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    a3-8 (FSR+) - a3-4 (FSR-)
    Always
    Below 1 Ω



NG
Go to step 12
OK


4.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT)


    C169178E01
  1. Disconnect SST from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    a3-8 (FSR+) - a3-4 (FSR-)
    Always
    1 MΩ or higher



NG
Go to step 13
OK


5.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT TO GROUND)


    C169178E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    a3-8 (FSR+) - Body ground
    Always
    1 MΩ or higher
    a3-4 (FSR-) - Body ground
    Always
    1 MΩ or higher



NG
Go to step 14
OK


6.RECHECK DTC
  1. Connect the connectors to the occupant classification ECU and the center airbag sensor assembly.

  1. Connect Techstream to the DLC3.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG).

  1. Clear the DTCs stored in the occupant classification ECU (Click here).

  1. Clear the DTCs stored in the center airbag sensor assembly (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG).

  1. Using Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1790 is not output.

    HINT:
    Codes other than DTC B1790 may be output at this time, but they are not related to this check.



NG
Go to step 7
OK

USE SIMULATION METHOD TO CHECK (Click here)  

7.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


8.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Using Techstream, perform "zero point calibration" (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.


NEXT


9.PERFORM SENSITIVITY CHECK
  1. Using Techstream, perform "sensitivity check" (Click here).

    Standard:
    27 to 33 kg (59.52 to 72.75 lb)


NEXT


10.RECHECK DTC
  1. Turn the ignition switch on (IG).

  1. Clear the DTCs stored in the occupant classification ECU (Click here).

  1. Clear the DTCs stored in the center airbag sensor assembly (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG).

  1. Using Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1790 is not output.

    HINT:
    Codes other than DTC B1790 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END 

11.CHECK FLOOR WIRE NO. 2 (SHORT TO B+)


    C169180E01
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the front seat wire RH connector from the floor wire No. 2.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Na1-1 (FSR+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    Na1-4 (FSR-) - Body ground
    Ignition switch on (IG)
    Below 1 V



NG
REPLACE FLOOR WIRE NO. 2
OK

REPLACE FRONT SEAT WIRE RH 

12.CHECK FLOOR WIRE NO. 2 (OPEN)


  1. Disconnect the front seat wire RH connector from the floor wire No. 2.


    C169181E01

    HINT:
    SST has already been inserted into connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Na1-1 (FSR+) - Na1-4 (FSR-)
    Always
    Below 1 Ω



NG
REPLACE FLOOR WIRE NO. 2
OK

REPLACE FRONT SEAT WIRE RH 

13.CHECK FLOOR WIRE NO. 2 (SHORT)


    C169180E01
  1. Disconnect the front seat wire RH connector from the floor wire No. 2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Na1-1 (FSR+) - Na1-4 (FSR-)
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE NO. 2
OK

REPLACE FRONT SEAT WIRE RH 

14.CHECK FLOOR WIRE NO. 2 (SHORT TO GROUND)


    C169180E01
  1. Disconnect the front seat wire RH connector from the floor wire No. 2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Na1-1 (FSR+) - Body ground
    Always
    1 MΩ or higher
    Na1-4 (FSR-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE NO. 2
OK

REPLACE FRONT SEAT WIRE RH