OCCUPANT CLASSIFICATION SYSTEM > Trouble in Passenger Airbag ON/OFF Indicator |
| Front Passenger Seat Condition | Passenger Airbag ON/OFF Indicator | SRS Warning Light | |
| ON Indicator | OFF Indicator | ||
| Vacant | OFF | OFF | OFF |
| Adult is seated. | ON | OFF | OFF |
| Child is seated. | OFF | ON | OFF |
| Child restraint system is set. | OFF | ON | OFF |
| Occupant classification system failure | OFF | ON | ON |
| 1.CHECK SRS WARNING LIGHT |
Turn the ignition switch on (IG), and check the SRS warning light condition.
|
| ||||
| OK | |
| 2.PERFORM ZERO POINT CALIBRATION |
Turn the ignition switch off.
Connect Techstream to the DLC3.
Turn the ignition switch on (IG).
Using Techstream, perform "zero point calibration" (Click here).
|
| ||||
| OK | |
| 3.PERFORM SENSITIVITY CHECK |
Using Techstream, perform "sensitivity check" (Click here).
|
| ||||
| OK | ||
| ||
| 4.RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT |
Turn the ignition switch off.
Loosen the 4 installation bolts of the front seat assembly RH.
Tighten the 4 installation bolts of the front seat assembly RH to the specified torque.
| NEXT | |
| 5.PERFORM ZERO POINT CALIBRATION |
Connect Techstream to the DLC3.
Turn the ignition switch on (IG).
Using Techstream, perform "zero point calibration" (Click here).
|
| ||||
| OK | |
| 6.PERFORM SENSITIVITY CHECK |
Using Techstream, perform "sensitivity check" (Click here).
|
| ||||
| OK | ||
| ||
| 7.READ VALUE USING PASSENGER SIDE BUCKLE SWITCH |
Turn the ignition switch on (IG).
Using Techstream, read the "Data List" (Click here).
Read the display when the passenger side buckle switch is operated.
| Tester Display | Measurement Item / Range | Normal Condition | Diagnostic Note |
| Passenger Buckle SW | Passenger side buckle switch/ Set: The seat belt is fastened Unset: The seat belt is not fastened NG: Data is not determined | Unset/Set | - |
|
| ||||
| OK | |
| 8.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery.
Disconnect the connectors from the occupant classification ECU and the 4 occupant classification sensors.
Check that the terminals of connectors are not damaged.
|
| ||||
| OK | |
| 9.REPLACE OCCUPANT CLASSIFICATION ECU |
Connect the connectors to the 4 occupant classification sensors.
Replace the occupant classification ECU (Click here).
| NEXT | |
| 10.PERFORM ZERO POINT CALIBRATION |
Connect the negative (-) terminal cable to the battery.
Connect Techstream to the DLC3.
Turn the ignition switch on (IG).
Using Techstream, perform "zero point calibration" (Click here).
| NEXT | |
| 11.PERFORM SENSITIVITY CHECK |
Using Techstream, perform "sensitivity check" (Click here).
| NEXT | ||
| ||
| 12.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery.
Disconnect the connectors from the occupant classification ECU and the front seat inner belt assembly RH.
Check that the terminals of connectors are not damaged.
|
| ||||
| OK | |
| 13.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH |
Connect the connector to the occupant classification ECU.
Replace the front seat inner belt assembly RH (Click here).
| NEXT | |
| 14.PERFORM ZERO POINT CALIBRATION |
Connect the negative (-) terminal cable to the battery.
Connect Techstream to the DLC3.
Turn the ignition switch on (IG).
Using Techstream, perform "zero point calibration" (Click here).
| NEXT | |
| 15.PERFORM SENSITIVITY CHECK |
Using Techstream, perform "sensitivity check" (Click here).
| NEXT | ||
| ||