Home › SUSPENSION & AXLE › SUSPENSION › FRONT LOWER BALL JOINT

FRONT LOWER BALL JOINT > REMOVAL

for Preparation Click here



1. REMOVE FRONT WHEEL


2. REMOVE FRONT AXLE HUB NUT


    C167528E01
  1. Using SST and a hammer, release the staked part of the front axle hub nut.

    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the threads of the drive shaft may be damaged.

  1. While applying the brakes, remove the front axle hub nut.



3. SEPARATE FRONT SPEED SENSOR


    C165819E01
  1. Remove the bolt and resin clamp, and separate the front speed sensor.

    NOTICE:
    1. Be sure to completely separate the front speed sensor from the front shock absorber with coil spring.
    2. Be careful not to damage the front speed sensor.
    3. Clean the installation hole and the surface for the speed sensor every time the speed sensor is removed.



4. SEPARATE FRONT DRIVE SHAFT ASSEMBLY


    C165537E04
  1. Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.



    C165534
  1. Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

    NOTICE:
    Loosen the staked part of the front axle hub nut completely, otherwise the threads of the drive shaft may be damaged.



5. SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY


    C165913
  1. Remove the 2 bolts and separate the front disc brake caliper assembly.

    NOTICE:
    Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.



6. REMOVE FRONT DISC


    C165879E01
  1. Remove the front disc.

    HINT:
    Put matchmarks on the disc and the axle hub.



7. SEPARATE TIE ROD ASSEMBLY
  1. Remove the cotter pin and the nut.



    C165542E01
  1. Install SST to the tie rod end.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure that the upper ends of the tie rod end and SST are aligned.



  1. Using SST, separate the tie rod end from the steering knuckle.


    C165543E01

    SST
    09960-20010   (09961-02010)

    NOTICE:
    1. When securing SST to the steering knuckle, be sure to tighten the string of SST to prevent it from falling.
    1. Install SST so that A and B are parallel.
    1. Be sure to place the wrench on the part indicated in the illustration.
    1. Do not damage the front disc brake dust cover.
    1. Do not damage the ball joint dust cover.
    1. Do not damage the steering knuckle.



8. SEPARATE FRONT LOWER SUSPENSION ARM


    C165929
  1. Remove the bolt, 2 nuts, and separate the front lower suspension arm from the lower ball joint.



9. REMOVE FRONT AXLE ASSEMBLY


    C165930
  1. Remove the 2 bolts, 2 nuts and front axle assembly.

    NOTICE:
    When removing the nuts, keep the bolts from rotating.



10. REMOVE FRONT LOWER BALL JOINT


    C167239
  1. Secure the front axle assembly in a vise using aluminum plates.

    NOTICE:
    When using a vise, do not overtighten it.



    C165931
  1. Remove the cotter pin and nut.



    C165932E02
  1. Install SST to the front lower ball joint as shown in the illustration.

    SST
    09960-20010   (09961-02050, 09961-02050)

    NOTICE:
    Check that the clearance measurement between SST and the front axle assembly is 1 mm (0.04 in.).



    C165933E01
  1. Using SST, remove the front lower ball joint from the front axle assembly as shown in the illustration.

    SST
    09960-20010   (09961-02010, 09961-02050, 09961-02050)

    NOTICE:
    1. Install SST so that A and B are parallel.
    2. Be sure to place a wrench on the part indicated in the illustration.
    3. Do not damage the front lower ball joint dust cover.