Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using Techstream to read the DATA LIST allows values or status of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the DATA LIST information early in troubleshooting is one way to save diagnostic time.

CAUTION:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect Techstream to the DLC3.

  2. Turn the ignition switch on (IG).

  3. Turn on Techstream.

  4. Enter the following menus.

    1. Select: Body / D-Door Motor / DATA LIST.

      D-Door Motor: 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      D Door P/W Auto SW
      Driver door power window auto switch signal/ON or OFF
      ON: Driver door power window auto switch operates
      OFF: Driver door power window auto switch does not operate
      -
      D Door P/W Up SW
      Driver door power window manual up switch signal/ON or OFF
      ON: Driver door power window manual up switch operates
      OFF: Driver door power window manual up switch does not operate
      -
      D Door P/W Down SW
      Driver door power window manual down switch signal/ON or OFF
      ON: Driver door power window manual down switch operates
      OFF: Driver door power window manual down switch does not operate
      -
      Glass Position (Close - 1/4)
      Jam protection operation within range of fully closed to 1/4 open window glass position/OK or CAUTION
      OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
      -
      Glass Position (1/4 - 2/4)
      Jam protection operation within range of 1/4 to 1/2 open window glass position/OK or CAUTION
      OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
      -
      Glass Position (2/4 - 3/4)
      Jam protection operation within range of 1/2 to 3/4 open window glass position/OK or CAUTION
      OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
      -
      Glass Position (3/4 - Open)
      Jam protection operation within range of 3/4 to fully open window glass position/OK or CAUTION
      OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
      -
      Number of Trouble codes
      Number of DTC recorded / min.: 0, max.: 255
      Min.: 0
      Max.: 255
      -

    2. Select: Body / Main Body / DATA LIST.

      Main Body: 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Communication D Door Motor
      Connection status between power window regulator motor assembly (driver door) and main body ECU (Instrument panel junction block)/OK/Stop
      OK: Communication is normal
      STOP: Communication is stopped
      -
      D Door Courtesy SW
      Driver side door courtesy switch signal/ON or OFF
      ON: Driver side door is open
      OFF: Driver side door is closed
      -


ACTIVE TEST

HINT:
Using Techstream to perform ACTIVE TESTS allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. DATA LIST information can be displayed while performing ACTIVE TESTS.

  1. Connect Techstream to the DLC3.

  2. Turn the ignition switch on (IG).

  3. Turn on Techstream.

  4. Enter the following menus.

    1. Select: Body / D-Door Motor / Active Test.

      D-Door Motor: 
      Tester Display
      Test Part
      Control Range
      Diagnostic Note
      Power Window
      Power window
      UP or OFF
      -
      Power Window
      Power window
      DOWN or OFF
      -

    2. Select: Body / Main Body / Active Test.

      Main Body: 
      Tester Display
      Test Part
      Control Range
      Diagnostic Note
      IG OFF P/W Control Permission Output
      Power window
      ON or OFF (After ignition switch is turned off)
      -