ENGINE IMMOBILISER SYSTEM (w/o Smart Key System) > REGISTRATION |
| 1. DESCRIPTION OF CODE REGISTRATION |
When adding master keys or sub keys (Additional registration):
Register the key code (immobiliser code) in the transponder key ECU.
| Target ECU | Refer to |
| Transponder key ECU | Procedure "B" |
When replacing the transponder key ECU (New registration):
Register the key code (immobiliser code) in the transponder key ECU.
| Target ECU | Refer to |
| Transponder key ECU | Procedure "A" |
Register the ECU communication ID between the new transponder key ECU and the ECM.
| Target ECU | Refer to |
| ECM | Procedure "D" |
When replacing the ECM:
Register the ECU communication ID between the transponder key ECU and the new ECM.
| Target ECU | Refer to |
| Transponder key ECU | Procedure "E" |
When replacing the transponder key ECU and the ECM:
Register the key codes (immobiliser codes) in the new transponder key ECU.
| Target ECU | Refer to |
| Transponder key ECU | Procedure "A" |
Register the ECU communication ID between the new transponder key ECU and the new ECM.
| Target ECU | Refer to |
| Transponder key ECU | Procedure "E" |
When erasing the key code(s):
Erase the key code(s) of lost key(s).
| Target ECU | Refer to |
| Transponder key ECU | Procedure "C" |
| 2. KEY REGISTRATION |
New key code registration (Procedure "A"):
| Procedure | Security Indicator Light Condition |
| 1. Start | Blinking
|
| 2. Insert the master key into the ignition key cylinder. | ON |
3. Techstream operation
| OFF for 1 second and then ON |
| 4. Remove the key and then push the Next button on the tester. | ON |
| 5. Insert the master key to be registered and then push the Next button on the tester. | OFF for 1 second and then ON |
| 6. Remove the key and then push the Next button on the tester. | ON |
| 5. Insert the sub-key to be registered and then push the Next button on the tester. | OFF for 1 second and then ON for 0.5 seconds and then OFF |
| 8. Remove the key. | Blinking |
| 7. End (Procedure "E") | |

Finish the automatic key code registration mode. The automatic key code registration mode can be forced to end when at least 1 key code (immobiliser code) for the master key has been registered.
| 3. REGISTRATION OF ADDITIONAL KEY |
Additional registration (Procedure "B"):
| Procedure | Time to Complete Operation | Security Indicator Light Condition |
| 1. Start | - | Blinking
|
| 2. Insert the already registered master key into the ignition key cylinder and turn the ignition switch on. | - | OFF |
3. Techstream operation
| Within 120 sec. | ON |
| 4. Remove the master key. | Within 20 sec.
| ON |
| 5. Insert the key to be registered in the ignition key cylinder. | Within 10 sec. | Blinking |
6. Wait for 60 sec. after the key is registered.
| - | OFF |
| 7. Remove the key. | - | Blinking |
| 8. End | ||
| 4. ERASURE OF KEY CODE |
Erase key codes (Procedure "C").
| Procedure | Time to Complete Operation | Security Indicator Light Condition |
| 1. Start | - | Blinking
|
| 2. Insert the already registered master key in the ignition key cylinder and turn the ignition switch on. | - | OFF |
3. Techstream operation
| Within 120 sec. | ON for 1 sec. then OFF |
| 4. Remove the master key. | Within 10 sec.
| ON |
| 5. End | ||
| 5. ECU COMMUNICATION ID REGISTRATION |
ECU communication ID registration (Procedure "D"):
Using SST, connect terminals TC and CG of the DLC3.

Turn the ignition switch to the ON position and leave the vehicle as is for 30 minutes.
Check that the engine starts.
ECU communication ID registration (Procedure "E"):
| Procedure | Security Indicator Light Condition |
| 1. Start | OFF |
| 2. Insert an already registered key into the ignition key cylinder. | |
| 3. Engine start | |
| 4. Check that the engine starts and stays on for more than 3 seconds. | |
| 5. Next | |
| 6. End | |