Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Speaker Circuit

for Preparation Click here


DESCRIPTION

  1. If the vehicle has a built-in type amplifier, a sound signal is sent from the radio receiver to the speakers via the "Standard Models" circuit.
  2. If the vehicle has a separate type amplifier, a sound signal from the radio receiver is amplified by the stereo component amplifier and then transmitted to the speaker via the "Premium Models" circuit.
If there is a short in this circuit, the stereo component amplifier detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier or speakers.

WIRING DIAGRAM


E153382E05


E152199E10


E152200E01


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR


    E151921E02
  1. Disconnect the connectors shown in the illustration from the stereo component amplifier or radio receiver and speakers.



    E151922E07
  1. Premium models:
    Measure the resistance between each of the front No. 2 speakers and the stereo component amplifier to check for an open circuit in the wire harness.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N16-8 (FL+) - F3-1
    Always
    Below 1 Ω
    N16-7 (FL-) - F3-2
    Always
    Below 1 Ω
    N16-2 (FR+) - f1-1
    Always
    Below 1 Ω
    N16-6 (FR-) - f1-2
    Always
    Below 1 Ω

  1. Standard models:
    Measure the resistance between each of the front No. 2 speakers and the radio receiver to check for an open circuit in the wire harness.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E8-2 (FL+) - F4-2
    Always
    Below 1 Ω
    E8-6 (FL-) - F4-4
    Always
    Below 1 Ω
    E8-1 (FR+) - f2-2
    Always
    Below 1 Ω
    E8-5 (FR-) - f2-4
    Always
    Below 1 Ω

  1. Premium models:
    Measure the resistance between each of the front No. 1 speakers and the stereo component amplifier to check for an open circuit in the wire harness.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N15-2 (FL+) - H5-1
    Always
    Below 1 Ω
    N15-1 (FL-) - H5-2
    Always
    Below 1 Ω
    N15-9 (FR+) - G5-1
    Always
    Below 1 Ω
    N15-3 (FR-) - G5-2
    Always
    Below 1 Ω

  1. Standard models:
    Measure the resistance between each of the front No. 1 speakers and the radio receiver to check for an open circuit in the wire harness.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E8-2 (FL+) - H5-1
    Always
    Below 1 Ω
    E8-6 (FL-) - H5-2
    Always
    Below 1 Ω
    E8-1 (FR+) - G5-1
    Always
    Below 1 Ω
    E8-5 (FR-) - G5-2
    Always
    Below 1 Ω

  1. Premium models:
    Measure the resistance between each of the rear speakers and the stereo component amplifier to check for an open circuit in the wire harness.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N16-3 (RL+) - K1-1
    Always
    Below 1 Ω
    N16-9 (RL-) - K1-2
    Always
    Below 1 Ω
    N16-10 (RR+) - J1-1
    Always
    Below 1 Ω
    N16-4 (RR-) - J1-2
    Always
    Below 1 Ω

  1. Standard models:
    Measure the resistance between each of the rear speakers and the radio receiver to check for an open circuit in the wire harness.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E9-2 (RL+) - K1-1
    Always
    Below 1 Ω
    E9-6 (RL-) - K1-2
    Always
    Below 1 Ω
    E9-1 (RR+) - J1-1
    Always
    Below 1 Ω
    E9-3 (RR-) - J1-2
    Always
    Below 1 Ω

  1. Premium models:
    Measure the resistance between each of the rear stereo component speaker and the stereo component amplifier to check for an open circuit in the wire harness.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N15-5 (WFL+) - T6-4 (WF+)
    Always
    Below 1 Ω
    N15-12 (WFL-) - T6-3 (WF-)
    Always
    Below 1 Ω
    N15-4 (WFR+) - T6-1 (WF+)
    Always
    Below 1 Ω
    N15-10 (WFR-) - T6-2 (WF-)
    Always
    Below 1 Ω

  1. Premium models:
    Measure the resistance between each speaker and body ground to check for a short circuit in the wire harness.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N16-8 (FL+) - Body ground
    Always
    10 kΩ or higher
    N16-7 (FL-) - Body ground
    Always
    10 kΩ or higher
    N16-2 (FR+) - Body ground
    Always
    10 kΩ or higher
    N16-6 (FR-) - Body ground
    Always
    10 kΩ or higher
    N16-3 (RL+) - Body ground
    Always
    10 kΩ or higher
    N16-9 (RL-) - Body ground
    Always
    10 kΩ or higher
    N16-10 (RR+) - Body ground
    Always
    10 kΩ or higher
    N16-4 (RR-) - Body ground
    Always
    10 kΩ or higher
    N15-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    N15-1 (FL-) - Body ground
    Always
    10 kΩ or higher
    N15-9 (FR+) - Body ground
    Always
    10 kΩ or higher
    N15-3 (FR-) - Body ground
    Always
    10 kΩ or higher
    N15-5 (WFL+) - Body ground
    Always
    10 kΩ or higher
    N15-12 (WFL-) - Body ground
    Always
    10 kΩ or higher
    N15-4 (WFR+) - Body ground
    Always
    10 kΩ or higher
    N15-10 (WFR-) - Body ground
    Always
    10 kΩ or higher

  1. Standard models:
    Measure the resistance between each speaker and body ground to check for a short circuit in the wire harness.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E8-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    E8-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    E8-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    E8-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    E9-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    E9-6 (RL-) - Body ground
    Always
    10 kΩ or higher
    E9-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    E9-3 (RR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT FRONT NO. 1 SPEAKER
  1. Resistance check

    1. Measure the resistance between the terminals of the speaker.

      Standard resistance:
      Premium models:
      Tester Connection
      Condition
      Specified Condition
      H5-1 - H5-2
      Always
      1.8 to 2.6 Ω
      G5-1 - G5-2
      Always
      1.8 to 2.6 Ω
      Standard models:
      Tester Connection
      Condition
      Specified Condition
      H5-1 - H5-2
      Always
      Approximately 4 Ω
      G5-1 - G5-2
      Always
      Approximately 4 Ω



NG
REPLACE FRONT NO. 1 SPEAKER
OK


3.INSPECT FRONT NO. 2 SPEAKER
  1. Check that the malfunction disappears when another speaker in good condition is installed.

    OK:
    Malfunction disappears.

    HINT:
    1. Connect all the connectors to the front No. 2 speaker.
    2. When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.



NG
Go to step 4
OK

REPLACE FRONT NO. 2 SPEAKER  

4.CONFIRM MODEL

Result:

Result
Proceed to
Premium models
A
Standard models
B



B
Go to step 7
A


5.INSPECT REAR SPEAKER
  1. Resistance check

    1. Measure the resistance between the terminals of the speaker.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      K1-1 - K1-2
      Always
      Approximately 4 Ω
      J1-1 - J1-2
      Always
      Approximately 4 Ω



NG
REPLACE REAR SPEAKER
OK


6.INSPECT REAR STEREO COMPONENT SPEAKER


    E147418E01
  1. Rear stereo component speaker:

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      T6-1 (WF+) - T6-2 (WF-)
      Always
      1.6 to 2.4 Ω
      T6-4 (WF+) - T6-3 (WF-)
      Always
      1.6 to 2.4 Ω

      NOTICE:
      The speaker should not be removed when checking resistance.



NG
REPLACE REAR STEREO COMPONENT SPEAKER
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

7.INSPECT REAR SPEAKER
  1. Resistance check

    1. Measure the resistance between the terminals of the speaker.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      K1-1 - K1-2
      Always
      Approximately 4 Ω
      J1-1 - J1-2
      Always
      Approximately 4 Ω



NG
REPLACE REAR SPEAKER
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)