DTC P0451 Evaporative Emission Control System Pressure Sensor Range / Performance |
DTC P0452 Evaporative Emission Control System Pressure Sensor / Switch Low Input |
DTC P0453 Evaporative Emission Control System Pressure Sensor / Switch High Input |
| DTCs | Monitoring Item | Malfunction Detection Condition | Trouble Area | Detection Timing | Detection Logic |
| P0451 | Canister pressure sensor abnormal voltage fluctuation | Sensor output voltage fluctuates frequently in a certain time period. |
|
| 2 trip |
| P0451 | Canister pressure sensor constant voltage | Sensor output voltage does not vary in a certain time period. | EVAP monitoring (ignition switch off) | 2 trip | |
| P0452 | Canister pressure sensor voltage low | Sensor output voltage is less than 0.45 V for 0.5 seconds. |
| 1 trip | |
| P0453 | Canister pressure sensor voltage high | Sensor output voltage is more than 4.9 V for 0.5 seconds. |
| 1 trip |

| Related DTCs | P0451: Evaporative emission control system canister pressure sensor noise P0451: Evaporative emission control system canister pressure sensor stuck P0452: Evaporative emission control system canister pressure sensor/switch low input P0453: Evaporative emission control system canister pressure sensor/switch high input |
| Required Sensors / Components | Canister pump module |
| Frequency of Operation | Once per driving cycle: P0451 sensor stuck Continuous: P0451 sensor noising, P0452 and P0453 |
| Duration | Less than 15 seconds: P0451 (Pressure sensor noise) Within 2 minutes: P0451 (Pressure sensor stuck) 0.5 seconds: P0452, P0453 |
| MIL Operation | Immediate: P0452, P0453 2 driving cycles: P0451 |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | None |
| Atmospheric pressure | 70 to 110 kPa (525 to 825 mmHg) |
| Battery voltage | 10.5 V or more |
| Intake air temperature | 4.4 to 35°C (40 to 95°F) |
| EVAP pressure sensor malfunction (P0452, P0453) | Not detected |
| Either of the following conditions 1 or 2 is met | - |
| 1. Engine condition | Running |
| 2. Time after key-off | 5 or 7 or 9.5 hours |
| Battery voltage | 10.5 V or more |
| Intake air temperature | 4.4 to 35°C (40 to 95°F) |
| EVAP pressure sensor malfunction (P0452, P0453) | Not detected |
| Atmospheric pressure | 70 to 110 kPa (525 to 825 mmHg) |
| Time after key-off | 5 or 7 or 9.5 hours |
| Ignition switch | on (IG) |
| Battery voltage | 8 V or more |
| Starter | OFF |
| Frequency that EVAP pressure change is 0.3 kPa (2.25 mmHg) or more | 10 times or more in 10 seconds |
| EVAP pressure change during reference pressure measurement | Less than 0.65 kPa (4.876 mmHg) |
| EVAP pressure | Less than 42.11 kPa (316 mmHg) |
| EVAP pressure | More than 123.761 kPa (928 mmHg) |

| 1.CONFIRM DTC AND EVAP PRESSURE |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG) (do not start the engine).
Turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Trouble Code.
Read DTCs.
Select the following menu items: Powertrain / Engine and ECT / Data List / EVAP / Vapor Pressure Pump.
Read the EVAP (Evaporative Emission) pressure displayed on the tester.
| Display (DTC Output) | Test Result | Suspected Trouble Area | Proceed to |
| P0451 | - | Canister pressure sensor | C |
| P0452 | Less than 45 kPa-a (336 mmHg-a) |
| A |
| P0453 | More than 120 kPa-a (900 mmHg-a) |
| B |
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |
![]() |
Turn the ignition switch off.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Test Result | Suspected Trouble Area | Proceed to |
| D35-22 (PPMP) - Body ground | Always | 10 Ω or less |
| A |
| 10 kΩ or more |
| B |
Reconnect the ECM connector.
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |
![]() |
Disconnect the canister pump module connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Test Result | Suspected Trouble Area | Proceed to |
| D35-22 (PPMP) - Body ground | Always | 10 kΩ or more | Short in canister pressure sensor circuit | A |
| 10 Ω or less | Short in wire harness/connector (ECM - Canister pressure sensor) | B |
Reconnect the canister pump module connector.
Reconnect the ECM connector.
|
| ||||
|
| ||||
| 4.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |
![]() |
Disconnect the canister pump module connector.
Turn the ignition switch on (IG).
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| N8-4 - Body ground | Ignition switch on (IG) | 4.5 to 5.5 V |
| N8-3 - Body ground | Ignition switch on (IG) | 4.5 to 5.5 V |
| Tester Connection | Condition | Specified Condition |
| N8-2 - Body ground | Always | 100 Ω or less |
| Test Result | Suspected Trouble Area | Proceed to |
| Voltage and resistance within standard ranges | Open in canister pressure sensor circuit | A |
| Voltage and resistance outside standard ranges | Open in wire harness/connector (ECM - Canister pressure sensor) | B |
Reconnect the canister pump module connector.
|
| ||||
|
| ||||
| 5.REPLACE CHARCOAL CANISTER ASSEMBLY |
Replace the canister assembly (Click here).

|
| ||||
| 6.REPAIR OR REPLACE HARNESS OR CONNECTOR (CANISTER PUMP MODULE - ECM) |
|
| ||||
| 7.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 8.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR) |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Wait for at least 60 seconds.
Select the following menu items: Powertrain / Engine and ECT / Trouble Code / Pending.
| NEXT | ||
| ||