Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › THROTTLE BODY

THROTTLE BODY > INSTALLATION

for Preparation Click here



1. INSTALL THROTTLE BODY


    A133820E01
  1. Install a new throttle body gasket to the intake air surge tank.



    A135709
  1. Install the throttle body with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



    A135708
  1. Connect the 2 water by-pass hoses.



    A135707
  1. Connect the throttle body connector and clamp.



2. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    A171941E01
  1. Install the air cleaner filter element, align the groove on the air cleaner hose with the throttle body alignment tab and tighten the clamp as shown in the illustration.

    HINT:
    1. A = 30°
    2. B = 11 to 14 mm (0.433 in. to 0.551 in.)

  1. Install the air cleaner cap with the 2 bolts and clips

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    A170887
  1. Connect the 3 vacuum hoses.



    A171944
  1. Connect the mass air flow meter connector.

  1. Connect the No. 2 ventilation hose and fuel vapor feed hose assembly.



3. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plugs

  1. Loosen the air drain cock plug from the water inlet housing.



    A169415E01
  1. Loosen the air drain plug at the top of the radiator 3 or 4 turns.

  1. Add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the engine air drain cock hole. Then tighten the air drain cock plug to the water inlet housing.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for air drain cock plug

  1. Continue to add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the radiator air drain hole. Then close the air drain plug at the top of the radiator.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf } for air drain plug

    HINT:
    If the coolant level at the radiator inlet opening drops after squeezing the No. 1 and No. 2 radiator hoses, add coolant.

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Standard capacity:
    w/o Trailer Towing System 
    Condition
    Specified Condition
    w/ Rear Heater
    11.0 liters (11.6 US qts, 9.7 Imp. qts)
    w/o Rear Heater
    8.8 liters (9.3 US qts, 7.7 Imp. qts)
    w/ Trailer Towing System 
    Condition
    Specified Condition
    w/ Rear Heater
    11.7 liters (12.4 US qts, 10.3 Imp. qts)
    w/o Rear Heater
    9.5 liters (10.1 US qts, 8.4 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Contact your TOYOTA dealer for further details.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by squeezing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

    2. Maintain the engine speed at 2500 to 3000 rpm.

    3. Squeeze the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When squeezing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

      NOTICE:
      1. Make sure that the radiator reservoir still has some coolant in it.
      2. If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
      3. If there is not enough coolant, the engine may overheat or be seriously damaged.
      4. If the radiator reservoir does not have enough coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the reservoir is filled to the FULL line.

  1. Stop the engine and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.



4. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

NOTICE:
Before performing each inspection, turn the A/C switch off.



    A169405
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.



5. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY


    C165926E01
  1. Install the outer cowl top panel sub-assembly with the 8 bolts and 6 nuts.

    Torque:
    Nut A:
    85 N*m{ 866 kgf*cm , 63 ft.*lbf }
    Bolt B:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }
    Nut C:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



    C165925
  1. Engage the 4 clamps.



6. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    E150150
  1. Install the windshield wiper motor and link assembly with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the connector.



7. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


  1. Engage the 20 claws.


    E150149

  1. Install the cowl top ventilator louver sub-assembly with the 2 clips.



    E150146
  1. Engage the 2 claws and connect the front fender to cowl side seal LH.



    E150147
  1. Engage the 2 claws and connect the front fender to cowl side seal RH.



8. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.



  1. When reinstalling:



      E112237E01
    1. Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.



    E147125E01
  1. Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    25.6 mm (1.00 in.)



9. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.



  1. When reinstalling:



      E112237E01
    1. Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.



    E152618E01
  1. Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    31.9 mm (1.26 in.)

  1. Operate the front wipers while spraying washer fluid onto the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.



10. INSTALL V-BANK COVER SUB-ASSEMBLY


    A162365
  1. Fit the 3 retainers and install the V-bank cover.



11. INSTALL NO. 1 ENGINE UNDER COVER


    A171855
  1. Install the No. 1 engine under cover with the 6 bolts and 2 clips.



12. INSTALL ENGINE UNDER COVER ASSEMBLY


    A171850
  1. Install the engine under cover assembly with the 4 bolts and 5 clips.



    A171849
  1. Install the engine under cover assembly RR with the 2 bolts.