Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK POWER WINDOW ECU (DRIVER SIDE)

B164268E05

  1. Disconnect the H1 switch connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Standard resistance:

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H1-1 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω


    Standard voltage:

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H1-2 (B) - Body ground
    SB - Body ground
    Power Supply
    Always
    11 to 14 V

    If the result is not as specified, there may be a malfunction in the wire harness.


CHECK POWER WINDOW MASTER SWITCH

B164269E06

  1. Disconnect the M1 switch connector.

  2. Measure the voltage and resistance of each terminal according to the value(s) in the table below.

    Standard resistance:

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M1-1 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω


    Standard voltage:

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M1-6 (B) - M1-1 (E)
    B - W-B
    Power supply
    Ignition switch on (IG)
    11 to 14 V
    Ignition switch off
    Below 1 V

    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the M1 switch connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Standard voltage:

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M1-16 (U) - M1-1 (E)
    W - W-B
    Power window motor UP output
    Ignition switch on (IG), front passenger side power window switch OFF
    Below 1 V
    Power window switch UP (Manual operation)
    11 to 14 V
    M1-15 (D) - M1-1 (E)
    SB - W-B
    Power window motor DOWN output
    Ignition switch on (IG), front passenger side power window switch OFF
    Below 1 V
    Power window switch DOWN (Manual operation)
    11 to 14 V
    M1-12 (U) - M1-1 (E)
    L - W-B
    Power window motor UP output
    Ignition switch on (IG), rear LH side power window switch OFF
    Below 1 V
    Power window switch UP (Manual operation)
    11 to 14 V
    M1-13 (D) - M1-1 (E)
    O - W-B
    Power window motor DOWN output
    Ignition switch on (IG), rear LH side power window switch OFF
    Below 1 V
    Power window switch UP (Manual operation)
    11 to 14 V
    M1-10 (U) - M1-1 (E)
    Y - W-B
    Power window motor UP output
    Ignition switch on (IG), rear RH side power window switch OFF
    Below 1 V
    Power window switch UP (Manual operation)
    11 to 14 V
    M1-18 (D) - M1-1 (E)
    LG - W-B
    Power window motor DOWN output
    Ignition switch on (IG), rear RH side power window switch OFF
    Below 1 V
    Power window switch UP (Manual operation)
    11 to 14 V

    If the result is not as specified, there may be a malfunction in the wire harness.


CHECK POWER WINDOW SWITCH (FRONT PASSENGER)

B164270E06

  1. Disconnect the G7 switch connector.

  2. Measure the voltage according to the value(s) in the table below.

    Standard voltage:

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G7-3 (B) - Body ground
    O - Body ground
    Power supply
    Ignition switch on (IG)
    11 to 14 V
    Ignition switch off
    Below 1 V

    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the G7 switch connector.

  4. Measure the voltage according to the value(s) in the table below.

    Standard voltage:

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G7-4 (U) - Body ground
    G - Body ground
    Power window motor UP output
    Ignition switch on (IG), front passenger side power window switch OFF
    Below 1 V
    Power window switch UP (Manual operation)
    11 to 14 V
    G7-1 (D) - Body ground
    Y - Body ground
    Power window motor DOWN output
    Ignition switch on (IG), front passenger side power window switch OFF
    Below 1 V
    Power window switch DOWN (Manual operation)
    11 to 14 V

    If the result is not as specified, the power window switch may have a malfunction.


CHECK POWER WINDOW SWITCH (REAR LH)

B164270E07

  1. Disconnect the K2 switch connector.

  2. Measure the voltage according to the value(s) in the table below.

    Standard voltage:

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K2-3 (B) - Body ground
    G - Body ground
    Power supply
    Ignition switch on (IG)
    11 to 14 V
    Ignition switch off
    Below 1 V

    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the K2 switch connector.

  4. Measure the voltage according to the value(s) in the table below.

    Standard voltage:

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K2-4 (U) - Body ground
    V - Body ground
    Power window motor UP output
    Ignition switch on (IG), rear LH side power window switch OFF
    Below 1 V
    Power window switch UP (Manual operation)
    11 to 14 V
    K2-1 (D) - Body ground
    SB - Body ground
    Power window motor DOWN output
    Ignition switch on (IG), rear LH side power window switch OFF
    Below 1 V
    Power window switch DOWN (Manual operation)
    11 to 14 V

    If the result is not as specified, the power window switch may have a malfunction.


CHECK POWER WINDOW SWITCH (REAR RH)

B164270E08

  1. Disconnect the J2 switch connector.

  2. Measure the voltage according to the value(s) in the table below.

    Standard voltage:

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J2-3 (B) - Body ground
    SB - Body ground
    Power supply
    Ignition switch on (IG)
    11 to 14 V
    Ignition switch off
    Below 1 V

    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the J2 switch connector.

  4. Measure the voltage according to the value(s) in the table below.

    Standard voltage:

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J2-4 (U) - Body ground
    V - Body ground
    Power window motor UP output
    Ignition switch on (IG), rear RH side power window switch OFF
    Below 1 V
    Power window switch UP (Manual operation)
    11 to 14 V
    J2-1 (D) - Body ground
    R - Body ground
    Power window motor DOWN output
    Ignition switch on (IG), rear RH side power window switch OFF
    Below 1 V
    Power window switch DOWN (Manual operation)
    11 to 14 V

    If the result is not as specified, the power window switch may have a malfunction.