WINDSHIELD GLASS > INSTALLATION |
| 1. INSTALL NO. 2 WINDSHIELD GLASS STOPPER |
Using a brush or sponge, coat the application area of the No. 2 windshield glass stoppers with Primer G.
Install 2 new No. 2 windshield glass stoppers onto the glass as shown in the illustration.

| 2. INSTALL NO. 1 WINDSHIELD GLASS STOPPER |
![]() |
Install 2 new No. 1 windshield glass stoppers to the vehicle body, as shown in the illustration.
| 3. INSTALL WINDOW GLASS ADHESIVE DAM |
Using a brush or sponge, coat the application area of the window glass adhesive dam with Primer G.
Install a new window glass adhesive dam onto the windshield glass, as shown in the illustration.

| 4. INSTALL WINDSHIELD GLASS |
![]() |
Position the windshield glass.
Using suction cups, place the glass in the correct position.
Check that the entire contact surface of the glass rim is perfectly even.
Place matchmarks on the glass and vehicle body on the locations indicated in the illustration.
Using suction cups, remove the glass.
Using a brush, apply Primer M to the exposed part of the vehicle body.

Using a brush or sponge, coat the application area of adhesive with Primer G.

| Area | Dimension |
| a | 8.6 mm (0.338 in.) |
| b | 8.0 mm (0.315 in.) |
Apply adhesive to the glass.
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Temperature | Usage Time Frame |
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour and 40 minutes |
| 5°C (41°F) | 8 hours |
Load the sealer gun with the cartridge.
Apply adhesive to the glass as shown in the illustration.

| Area | Dimension |
| a | 12.0 mm (0.472 in.) |
| b | 8.0 mm (0.315 in.) |
| c | 8.6 mm (0.338 in.) |
| d | 6.5 mm (0.256 in.) |
![]() |
Install the windshield glass assembly.
Using suction cups, position the glass so that the matchmarks are aligned. Press it in gently along the rim.
Lightly press the outer surface of the glass to ensure that it is securely fitted to the vehicle body.
![]() |
If necessary, use a scraper to correct the level or position of adhesive that has been applied.
Hold the windshield glass using protective tape until applied adhesive becomes hard.
| Temperature | Usage Time Frame |
| 35°C (95°F) | 1 hour and 30 minutes |
| 5°C (41°F) | 24 hours |
| 20°C (68°F) | 5 hours |
![]() |
Engage the connector and clamp. (w/ Deicer)
| 5. INSPECT FOR LEAK AND REPAIR |
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
| 6. INSTALL ROOF HEADLINING ASSEMBLY |
| 7. INSTALL VISOR HOLDER |
![]() |
Engage the 2 claws.
Push in the visor holder as shown in the illustration.
| 8. INSTALL ASSIST GRIP ASSEMBLY (w/ Sliding Roof) |
![]() |
Assemble the rear assist grip assembly as shown in the illustration.
![]() |
Install the rear assist grip sub-assembly.
| 9. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof) |
![]() |
Assemble the front assist grip sub-assembly as shown in the illustration.
![]() |
Install the front assist grip sub-assembly.
| 10. INSTALL VISOR ASSEMBLY LH |
![]() |
Install the visor assembly LH with the 2 screws.
| 11. INSTALL VISOR BRACKET COVER |
![]() |
Engage the 4 claws and install the visor bracket cover.
| 12. INSTALL VISOR ASSEMBLY RH |
| 13. INSTALL VISOR BRACKET COVER (for RH Side) |
| 14. INSTALL ROOF CONSOLE BOX ASSEMBLY |
![]() |
Connect the connector.
Engage the 3 guides, 2 clips, fastener, and install the roof console box assembly.
| 15. INSTALL FRONT PILLAR GARNISH LH |
![]() |
Remove the protective cover.
![]() |
Install a new clip <A> on the front pillar garnish LH.
Engage the 3 guides and 2 clips, then install the front pillar garnish LH.
| 16. INSTALL FRONT PILLAR GARNISH RH |
![]() |
Remove the protective cover.
![]() |
Install a new clip <A> on the front pillar garnish RH.
Engage the 3 guides and 2 clips, then install the front pillar garnish RH.
| 17. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
Engage the 20 claws.

Install the cowl top ventilator louver with the 2 clips.
| 18. INSTALL FRONT FENDER TO COWL SIDE SEAL LH |
![]() |
Engage the claw and install a new front fender to cowl side seal LH.
![]() |
Engage the 2 claws.
| 19. INSTALL FRONT FENDER TO COWL SIDE SEAL RH |
| 20. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
When reinstalling:
![]() |
Clean the wiper arm serrations.
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.
| Area | Measurement |
| A | 25.6 mm (1.00 in.) |
| 21. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
When reinstalling:
![]() |
Clean the wiper arm serrations.
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.
| Area | Measurement |
| A | 31.9 mm (1.26 in.) |
Operate the front wipers while spraying washer fluid onto the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.
| 22. INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror) |
![]() |
Slide the inner rear view mirror assembly in the direction indicated by the arrow shown in the illustration to install it.
![]() |
Engage the 2 claws and install the cover.
| 23. INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror) |
![]() |
Using a "TORX" socket wrench (T20), install the inner rear view mirror with the screw.
| 24. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror) |
![]() |
Engage the 2 claws and install the inner rear view mirror stay holder cover.
![]() |
Engage the 2 claws and install the inner rear view mirror stay holder cover as shown in the illustration.