WINDSHIELD GLASS > REMOVAL |
| 1. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror) |
![]() |
Disengage the 2 claws and the cover.
![]() |
Pull the lever in the direction indicated by the arrow shown in the illustration and slide the inner rear view mirror assembly upward to remove it.
| 2. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror) |
![]() |
Disengage the 2 claws and slide the inner rear view mirror stay holder cover as shown in the illustration.
![]() |
Disengage the 2 claws and remove the inner rear view mirror stay holder cover.
| 3. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror) |
![]() |
Disconnect the connector.
Using a "TORX" socket wrench (T20), remove the screw and the inner rear view mirror.
| 4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Remove the nut, and the front wiper arm and blade assembly LH.
| 5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH |
![]() |
Remove the nut, and the front wiper arm and blade assembly RH.
| 6. REMOVE FRONT FENDER TO COWL SIDE SEAL LH |
![]() |
Disengage the 2 claws.
![]() |
Disengage the 2 double-sided tapes.
Disengage the claw and remove the front fender to cowl side seal LH as shown in the illustration.
| 7. REMOVE FRONT FENDER TO COWL SIDE SEAL RH |
| 8. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
Remove the 2 clips.

Disengage the 20 claws and remove the cowl top ventilator louver sub-assembly.
| 9. REMOVE FRONT PILLAR GARNISH LH |
![]() |
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Cut off the clip <A>.
Disengage the 3 guides and remove the front pillar garnish LH.
Remove the clip <A>.
![]() |
Protect the curtain shield airbag assembly.
Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.
| 10. REMOVE FRONT PILLAR GARNISH RH |
![]() |
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Cut off the clip <A>.
Disengage the 3 guides and remove the front pillar garnish RH.
Remove the clip <A>.
![]() |
Protect the curtain shield airbag assembly.
Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.
| 11. REMOVE ROOF CONSOLE BOX ASSEMBLY |
![]() |
Using a moulding remover, disengage the 2 clips, 3 guides and fastener.
Disconnect the connector and remove the roof console box assembly.
| 12. REMOVE VISOR BRACKET COVER (for LH Side) |
![]() |
Remove the 2 screws and remove the visor assembly LH.
| 13. REMOVE VISOR ASSEMBLY LH |
![]() |
Remove the 2 screws and remove the visor assembly LH.
| 14. REMOVE VISOR BRACKET COVER (for RH Side) |
| 15. REMOVE VISOR ASSEMBLY RH |
| 16. REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof) |
![]() |
Using a screwdriver, disengage the 6 claws and remove the 2 assist grip covers.
![]() |
Disengage the 4 clips and remove the assist grip sub-assembly.
Remove the 4 clips from the vehicle body.
| 17. REMOVE ASSIST GRIP ASSEMBLY (w/ Sliding Roof) |
![]() |
Using a screwdriver, disengage the 6 claws and remove the 2 assist grip covers.
![]() |
Disengage the 4 clips and remove the assist grip assembly.
Remove the 4 clips from the vehicle body.
| 18. REMOVE VISOR HOLDER |
![]() |
Turn the visor holder approximately 45° and pull it out as shown in the illustration.
Disengage the 2 claws and remove the visor holder.
| 19. REMOVE ROOF HEADLINING ASSEMBLY |
| 20. REMOVE WINDSHIELD GLASS |
![]() |
Disconnect the connector and clamp. (w/ Deicer)
Disconnect the windshield glass stoppers.

![]() |
Apply protective tape to the installation position of the windshield glass sub-assembly on the vehicle body.
Pass a piano wire between the vehicle body and windshield glass sub-assembly from the interior.

Tie both wire ends to wooden blocks or similar objects.
Cut the adhesive by pulling the piano wire around the windshield glass sub-assembly.
![]() |
Place matchmarks on the windshield glass sub-assembly and vehicle body on the locations indicated in the illustration.
Using suction cups, remove the windshield glass sub-assembly.
| 21. REMOVE WINDOW GLASS ADHESIVE DAM |
Using a scraper, remove the windshield glass adhesive dam.
| 22. REMOVE NO. 2 WINDSHIELD GLASS STOPPER |
Using a scraper, remove the No. 2 window glass stoppers.
| 23. REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type) |
![]() |
Remove the 2 No. 1 windshield glass stoppers.
| 24. CLEAN WINDSHIELD GLASS |
![]() |
Using a scraper, remove the damaged stoppers, dams and adhesive sticking to the glass.
Clean the outer edges of the glass with a non-residue solvent.
| 25. CLEAN VEHICLE BODY |
![]() |
Clean and shape the contact surfaces of the vehicle body.
On the contact surfaces of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.
Clean the contact surfaces of the vehicle body with cleaner.