NAVIGATION SYSTEM > DIAGNOSIS DISPLAY DETAILED DESCRIPTION |
| SYSTEM CHECK |
System Check Mode Screen

Device Names and Hardware Address/*1
| Address No. | Name | Address No. | Name |
| 110 | EMV | 120 | AVX |
| 128 | 1DIN TV | 140 | AVN |
| 144 | G-BOOK | 178 | NAVI |
| 17C | MONET | 190 | AUDIO H/U |
| 1AC | CAMERA-C | 1B0 | Rr-TV |
| 1C0 | Rr-CONT | 19D | BT-HF |
| 1C4 | PANEL | 1C6 | G/W |
| 1C8 | FM-M-LCD | 1D8 | CONT-SW |
| 1EC | Body | 118 | EMVN |
| 1F1 | XM | 1F2 | SIRIUS |
| 230 | TV-TUNER | 240 | CD-CH2 |
| 250 | DVD-CH | 280 | CAMERA |
| 360 | CD-CH1 | 3A0 | MD-CH |
| 17D | TEL | 440 | DSP-AMP |
| 530 | ETC | 1F6 | RSE |
| 1A0 | DVD-P | 1D6 | CLOCK |
| 238 | DTV | 480 | AMP |
Check Result/*2
| Result | Meaning | Action |
| OK | The device does not respond with a DTC (excluding communication DTCs from the AVC-LAN). | - |
| EXCH | The device responds with a "replace"-type DTC. | Look up the DTC in "Unit Check Mode" and replace the device. |
| CHEK | The device responds with a "check"-type DTC. | Look up the DTC in "Unit Check Mode". |
| NCON | The device was previously present, but does not respond in diagnostic mode. |
|
| Old | The device responds with an "old"-type DTC. | Look up the DTC in "Unit Check Mode". |
| NRES | The device responds in diagnostic mode, but gives no DTC information. |
|
Code Clear/*3
Memory Clear/*4
Diagnosis MENU Screen

Unit Check Mode Screen

| Display | Contents |
| Device name/*1 | Target device |
| Segment/*2 | Target device logical address |
| DTC/*3 | DTC (Diagnostic Trouble Code) |
| Timestamp/*4 | The time and date of past DTCs are displayed. (The year is displayed in 2-digit format.) |
| Present code/*5 | DTCs output in the service check are displayed. |
| Past code/*6 | Diagnostic memory results and recorded DTCs are displayed. |
| Diagnosis clear switch/*7 | Pushing this switch for 3 seconds clears the diagnostic memory data of the target device. (Both response to diagnostic system check result and the displayed data are cleared.) |
LAN Monitor (Original) Screen

Check Result/*1
| Result | Meaning | Action |
| No Err (OK) | There are no communication DTCs. | - |
| CHEK | The device responds with a "check"-type DTC. | Look up the DTC in "Unit Check Mode". |
| NCON | The device was previously present, but does not respond in diagnostic mode. |
|
| Old | The device responds with an "old"-type DTC. | Look up the DTC in "Unit Check Mode". |
| NRES | The device responds in diagnostic mode, but gives no DTC information. |
|
LAN Monitor (Individual) Screen

| Display | Contents |
| Device name/*1 | Target device |
| Segment/*2 | Target logical address |
| DTC/*3 | DTC (Diagnostic Trouble Code) |
| Sub-code (device address)/*4 | Physical address stored with DTC (If there is no address, nothing is displayed.) |
| Connection check No./*5 | Connection check number stored with DTC |
| DTC occurrence/*6 | Number of times the same DTC has been recorded |
| Diagnosis clear switch/*7 | Pushing this switch for 3 seconds clears the diagnostic memory data of the target device. (Both response to diagnostic system check result and the displayed data are cleared.) |
| DISPLAY CHECK |
Vehicle Signal Check Mode Screen

| Display | Contents |
| Battery | Battery voltage is displayed. |
| PKB | Parking brake ON/OFF state is displayed. |
| REV | Reverse signal ON/OFF state is displayed. |
| IG | IG switch ON/OFF state is displayed. |
| TAIL | TAIL signal (Light control switch) ON/OFF state is displayed. |
| SPEED | Vehicle speed is displayed in km/h. |
| NAVIGATION CHECK |
Navigation Check Screen

GPS Information Screen

Satellite information/*1
Information from a maximum of 12 satellites is displayed on the screen. This information includes the target GPS satellite number, elevation angle, direction, and signal level.
Receiving condition/*2
| Display | Contents |
| T | The system is receiving a GPS signal, but is not using it for location. |
| P | The system is using the GPS signal for location. |
| - | The system cannot receive a GPS signal. |
| Display | Contents |
| 01H | The system cannot receive a GPS signal. |
| 02H | The system is tracing a satellite. |
| 03H | The system is receiving a GPS signal, but is not using it for location. |
| 04H | The system is using the GPS signal for location. |
| Display | Contents |
| 2D | 2-dimensional location method is being used. |
| 3D | 3-dimensional location method is being used. |
| NG | Location data cannot be used. |
| Error | Reception error has occurred. |
| - | Any other state. |
| Display | Contents |
| Position | Latitude and longitude information on the current position is displayed. |
| Display | Contents |
| Date | The date/time information obtained from GPS signal is displayed in Greenwich mean time (GMT). The last 4 digits are displayed. |
Vehicle Sensors Screen

| Display | Contents |
| REV/*1 | REV signal ON/OFF state is displayed. |
| SPD/*2 | SPD signal condition is displayed. |
| Display | Contents |
| Gyro sensor/*3 | Gyro sensor output condition is displayed (when the vehicle runs straight or is stationary, the voltage is approximately 2.5 V). |
Microphone & Voice Recognition Check Screen

| Display | Contents |
| Microphone input level meter/*1 | Monitors the microphone input level every 0.1 sec. and displays the results in 8 different levels. |
| Recording switch/*2 | Starts recording. |
| Stop switch/*3 | Stops recording. |
| Play switch/*4 | Plays the recorded voice. |
| Recording indicator/*5 | Comes on while recording. |
DVD Player Information Screen

| Display | Contents |
| Trouble code/*1 | Each code corresponding to the malfunctions is displayed. For details, refer to "Trouble Code Description". |
| Occurrence time/*2 |
|
| Trouble code clear switch/*3 | All code data being displayed are cleared by pushing this switch for 3 seconds. |
| Returning switch/*4 | The previous page is displayed. If the current displayed page is the first page, this switch cannot be operated. |
| Proceeding switch/*5 | The next page is displayed. If the current displayed page is the last page, this switch cannot be operated. |
| Code | Malfunction | Countermeasure |
| 01 | Cannot be recognized | Replace navigation receiver assembly. |
| 03 | Cannot be read | Follow the inspection procedure for DTC 58-42 (Click here). |