Home › TRANSMISSION · U151F AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

AUTOMATIC TRANSAXLE SYSTEM > Transmission Control Switch Circuit

for Preparation Click here


DESCRIPTION

When moving the shift lever into the S position using the transmission control switch, it is possible to switch the shift range position between "1" (first range) and "5" (fifth range).
Shifting up "+" once raises one shift range position, and shifting down "-" lowers one shift range position.

WIRING DIAGRAM


C171936E02


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - SHIFT LOCK CONTROL UNIT ASSEMBLY)


    C168574E06
  1. Disconnect the transmission control switch connector of shift lock control unit assembly.

  1. Turn the ignition switch on (IG), and measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D28-3 (IG) - Body ground
    Ignition switch on (IG)
    11 to 14 V
    ↑
    Ignition switch off
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - BODY GROUND)


    C168574E07
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D28-5 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY


    C168599E05
  1. Measure the resistance between each terminal of shift lock control unit assembly when the shift lever is moved to each position.

    Standard resistance (Check for short):
    Tester Connection
    Shift Position
    Specified Condition
    3 - 7
    S, "+" and "-"
    Below 1 Ω
    ↑
    Except S, "+" and "-"
    10 kΩ or higher
    2 - 5
    Press continuously
    "+"
    (Up shift)
    Below 1 Ω
    ↑
    S
    10 kΩ or higher
    1 - 5
    Press continuously
    "-"
    (Down shift)
    Below 1 Ω
    ↑
    S
    10 kΩ or higher



NG
REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - ECM)


    C168527E12
  1. Connect the transmission control switch connector of shift lock control unit assembly.

  1. Disconnect the ECM connector.

  1. Measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

    Standard voltage:
    Tester Connection
    Shift Position
    Specified Condition
    D36-20 (S) -
    Body ground
    S, "+" and "-"
    11 to 14 V
    ↑
    Except S, "+" and "-"
    Below 1 V



    C168527E13
  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

    Standard resistance:
    Tester Connection
    Shift Position
    Specified Condition
    D36-6 (SFTU) - Body ground
    Press continuously "+" (Up shift)
    Below 1 Ω
    ↑
    S
    10 kΩ or higher
    D36-5 (SFTD) - Body ground
    Press continuously "-" (Down shift)
    Below 1 Ω
    ↑
    S
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE