DTC B1650/32 Occupant Classification System Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1650/32 |
|
|

| 1.CHECK DTC (OCCUPANT CLASSIFICATION ECU) |
Turn the ignition switch on (IG).
Using Techstream, check the DTCs of the occupant classification ECU (Click here).
|
| ||||
| OK | |
| 2.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the occupant classification ECU. Also check that the connectors that link the front seat wire RH and floor wire are properly connected.
Disconnect the connectors from the center airbag sensor assembly and the occupant classification ECU. Also disconnect the connectors that link the front seat wire RH and floor wire.
Check that the connector terminals are not damaged.
|
| ||||
| OK | |
| 3.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (OPEN) |
Using SST, connect terminals 16 (FSP+) and 24 (FSP-) of connector B.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| a3-8 (FSR+) - a3-4 (FSR-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 4.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT) |
![]() |
Disconnect SST from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| a3-8 (FSR+) - a3-4 (FSR-) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 5.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| a3-8 (FSR+) - Body ground | Ignition switch on (IG) | Below 1 V |
| a3-4 (FSR-) - Body ground | Ignition switch on (IG) | Below 1 V |
|
| ||||
| OK | |
| 6.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT TO GROUND) |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| a3-8 (FSR+) - Body ground | Always | 1 MΩ or higher |
| a3-4 (FSR-) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||
| 7.CHECK FLOOR WIRE (OPEN) |
Disconnect the front seat wire RH connector from the floor wire.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| Na1-1 (FSR+) - Na1-4 (FSR-) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 8.CHECK FLOOR WIRE (SHORT) |
![]() |
Disconnect the front seat wire RH connector from the floor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| Na1-1 (FSR+) - Na1-4 (FSR-) | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||
| 9.CHECK FLOOR WIRE (SHORT TO B+) |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the front seat wire RH connector from the floor wire.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| Na1-1 (FSR+) - Body ground | Ignition switch on (IG) | Below 1 V |
| Na1-4 (FSR-) - Body ground | Ignition switch on (IG) | Below 1 V |
|
| ||||
| OK | ||
| ||
| 10.CHECK FLOOR WIRE (SHORT TO GROUND) |
![]() |
Disconnect the front seat wire RH connector from the floor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| Na1-1 (FSR+) - Body ground | Always | 1 MΩ or higher |
| Na1-4 (FSR-) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||