REAR DIFFERENTIAL CARRIER ASSEMBLY > REMOVAL |
| 1. REMOVE REAR WHEEL |
| 2. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY |
![]() |
Depress the brake pedal and hold it.
Using a hexagon wrench (6 mm), loosen the cross groove joint set bolts 1/2 turn.
![]() |
Place matchmarks on the rear propeller shaft and rear drive pinion flange sub-assembly.
Remove the 4 nuts, 4 bolts and 4 washers.
![]() |
Remove the 4 bolts and 4 adjusting shims.
![]() |
Using a brass bar and a hammer, remove the propeller shaft with center bearing shaft assembly.
![]() |
Insert SST into the transfer to prevent oil leakage.
| 3. REMOVE TAIL EXHAUST PIPE ASSEMBLY |
![]() |
Remove the 2 bolts and 2 compression springs.
Disconnect the exhaust pipe support and remove the tail exhaust pipe assembly.
Remove the gasket from the center exhaust pipe assembly.
| 4. REMOVE CENTER EXHAUST PIPE ASSEMBLY |
![]() |
Remove the 2 bolts and 2 compression springs.
Disconnect the 3 exhaust pipe supports and remove the center exhaust pipe assembly.
Remove the gasket from the No. 3 exhaust pipe sub-assembly.
| 5. REMOVE REAR SPEED SENSOR LH |
![]() |
Remove the bolt and separate the rear speed sensor from the rear axle carrier sub-assembly.
| 6. REMOVE REAR SPEED SENSOR RH |
| 7. REMOVE REAR AXLE SHAFT NUT LH |
![]() |
Using SST and a hammer, release the staked part of the rear axle shaft nut.
While applying the brakes, remove the rear axle shaft nut.
| 8. REMOVE REAR AXLE SHAFT NUT RH |
| 9. REMOVE REAR DISC BRAKE CALIPER ASSEMBLY LH |
![]() |
Remove the 2 bolts and separate the rear disc brake caliper assembly.
| 10. REMOVE REAR DISC BRAKE CALIPER ASSEMBLY RH |
| 11. REMOVE REAR DISC (for LH Side) |
![]() |
Put matchmarks on the rear disc and the axle hub.
![]() |
Release the parking brake and remove the rear disc.
| 12. REMOVE REAR DISC (for RH Side) |
| 13. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH |
![]() |
Put matchmarks on the drive shaft and axle hub.
![]() |
Remove the 4 bolts and the rear axle hub and bearing assembly.
| 14. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY RH |
| 15. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY |
![]() |
Remove the bolt and the nut, and separate the No. 3 parking brake cable assembly.
| 16. REMOVE NO. 2 PARKING BRAKE CABLE ASSEMBLY |
| 17. REMOVE REAR STRUT ROD ASSEMBLY (for LH Side) |
![]() |
Remove the 2 bolts, the 2 nuts, and the rear strut rod assembly.
| 18. REMOVE REAR STRUT ROD ASSEMBLY (for RH Side) |
| 19. REMOVE REAR AXLE CARRIER SUB-ASSEMBLY LH |
![]() |
Loosen the 2 bolts.
![]() |
Remove the 2 bolts and 2 nuts, and separate the rear shock absorber with coil spring (lower side) from the rear axle carrier sub-assembly.
![]() |
Remove the 2 bolts, the 2 nuts, and the rear axle carrier sub-assembly.
| 20. REMOVE REAR AXLE CARRIER SUB-ASSEMBLY RH |
| 21. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH |
![]() |
Put matchmarks on the adjust cams and the rear suspension member sub-assembly.
Remove the nut, the No. 2 camber adjust cam, the rear suspension toe adjust cam sub-assembly, and the rear No. 2 suspension arm assembly LH.
| 22. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH |
| 23. REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH |
![]() |
Remove the bolt, the nut, and the rear No. 1 suspension arm assembly RH from the rear suspension member sub-assembly.
| 24. REMOVE REAR DIFFERENTIAL FILLER PLUG |
![]() |
Using a hexagon wrench (10 mm), remove the rear differential filler plug and rear differential filler plug gasket.
| 25. REMOVE REAR DIFFERENTIAL DRAIN PLUG |
![]() |
Using a hexagon wrench (10 mm), remove the rear differential drain plug and rear differential drain plug gasket, and drain the oil.
| 26. REMOVE REAR DRIVE SHAFT ASSEMBLY LH |
![]() |
Using SST, remove the rear drive shaft assembly as shown in the illustration.
| 27. REMOVE REAR DRIVE SHAFT ASSEMBLY RH |
| 28. REMOVE REAR DRIVE SHAFT SNAP RING LH |
![]() |
Using a screwdriver, remove the rear drive shaft snap ring.
| 29. REMOVE REAR DRIVE SHAFT SNAP RING RH |
| 30. REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY |
![]() |
Support the rear suspension member with a jack using a wooden block.
![]() |
Remove the 4 nuts, 2 bolts and 2 rear lower suspension member stopper retainers.
Lower the rear suspension member.
Remove the 2 rear upper suspension member stoppers.
| 31. REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY |
![]() |
Support the rear differential carrier assembly with a jack.
Remove the 2 bolts and 2 lock nuts, and separate the No. 1 rear differential support from the rear suspension member sub-assembly.
![]() |
Remove the 3 bolts and rear differential carrier assembly from the rear suspension member sub-assembly.
| 32. REMOVE NO. 1 REAR DIFFERENTIAL SUPPORT |
![]() |
Remove the 2 bolts, 2 lock nuts and No. 1 rear differential support from the rear differential carrier assembly.