Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) > PTC Heater Circuit

for Preparation Click here


DESCRIPTION

PTC heater relays are closed in accordance with signals from the air conditioning amplifier and power is supplied to the PTC heater.

WIRING DIAGRAM


E174118E01


INSPECTION PROCEDURE

1.INSPECT FUSE (PTC NO. 1, PTC NO. 2, PTC NO. 3)
  1. Remove the PTC NO. 1, PTC NO. 2 and PTC NO. 3 fuses from the engine room No. 2 relay block.

  1. Measure the resistance of the fuses.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    PTC NO. 1
    Always
    Below 1 Ω
    PTC NO. 2
    Always
    Below 1 Ω
    PTC NO. 3
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


2.INSPECT PTC HEATER RELAY


    A092673E24
  1. Remove the No. 1, No. 2 and No. 3 PTC heater relays from the engine room No. 2 relay block.

  1. Measure the resistance of the relays.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage is not applied to terminals 1 and 2)
    10 kΩ or higher
    3 - 5
    When battery voltage is applied to terminals 1 and 2)
    Below 1 Ω



NG
REPLACE PTC HEATER RELAY
OK


3.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - BODY GROUND)


    E153678E04
  1. Remove the No. 1, No. 2 and No. 3 PTC heater relays from the engine room No. 2 relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    No. 1 PTC heater relay terminal 2 - Body ground
    Always
    Below 1 Ω
    No. 2 PTC heater relay terminal 2 - Body ground
    Always
    Below 1 Ω
    No. 3 PTC heater relay terminal 2 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - PTC HEATER RELAY)


    E153678E04
  1. Remove the No. 1, No. 2 and No. 3 PTC heater relays from the engine room No. 2 relay block.

  1. Turn the ignition switch on (IG).

  1. When the PTC heater operating conditions are met (engine at idling speed or faster, ambient temperature is 10°C (50°F) or less, engine coolant temperature is 65°C (149°F) or less, set temperature switch is set to MAX HOT), turn the blower switch to the LO setting.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    No. 1 PTC heater relay terminal 1 - Body ground
    Always
    11 to 14 V
    No. 2 PTC heater relay terminal 1 - Body ground
    Always
    11 to 14 V
    No. 3 PTC heater relay terminal 1 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (BATTERY - PTC HEATER RELAY)


    E153678E04
  1. Remove the No. 1, No. 2 and No. 3 PTC heater relays from the engine room No. 2 relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    No. 1 PTC heater relay terminal 5 - Body ground
    Always
    11 to 14 V
    No. 2 PTC heater relay terminal 5 - Body ground
    Always
    11 to 14 V
    No. 3 PTC heater relay terminal 5 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - PTC HEATER)


    E153679E03
  1. Remove the No. 1, No. 2 and No. 3 PTC heater relays from the engine room No. 2 relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    No. 1 PTC heater relay terminal 3 - D44-2 (B)
    Always
    Below 1 Ω
    No. 2 PTC heater relay terminal 3 - D44-3 (B)
    Always
    Below 1 Ω
    No. 3 PTC heater relay terminal 3 - D44-1 (B)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK AIR CONDITIONING AMPLIFIER


    E127567E15
  1. Remove the air conditioning amplifier with its connectors still connected.

  1. Turn the ignition switch on (IG).

  1. When the PTC heater operating conditions are met (engine at idling speed or faster, ambient temperature is 10°C (50°F) or less, engine coolant temperature is 65°C (149°F) or less, set temperature switch is set to MAX HOT), turn the blower switch to the Lo setting.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D37-3 (PTC1) - Body ground
    Always
    11 to 14 V
    D37-22 (PTC2) - Body ground
    Always
    11 to 14 V
    D37-4 (PTC3) - Body ground
    Always
    11 to 14 V



NG
REPLACE AIR CONDITIONING AMPLIFIER
OK


8.REPLACE PTC HEATER
  1. Replace the PTC heater .


NEXT


9.CHECK PTC HEATER (OPERATION)
  1. Operate the PTC heater to check that it functions properly.

    OK:
    PTC heater function operates normally.



NG
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK

END (PTC HEATER IS DEFECTIVE)