AIR CONDITIONING SYSTEM (for Manual Air Conditioning System) > PTC Heater Circuit |

| 1.INSPECT FUSE (PTC NO. 1, PTC NO. 2, PTC NO. 3) |
Remove the PTC NO. 1, PTC NO. 2 and PTC NO. 3 fuses from the engine room No. 2 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| PTC NO. 1 | Always | Below 1Ω |
| PTC NO. 2 | Always | Below 1Ω |
| PTC NO. 2 | Always | Below 1Ω |
|
| ||||
| OK | |
| 2.INSPECT PTC HEATER RELAY |
![]() |
Remove the No. 1, No. 2 and No. 3 PTC heater relays from the engine room No. 2 relay block.
Measure the resistance of the relays.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | when battery voltage is not applied to terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | when battery voltage is applied to terminals 1 and 2 | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - BODY GROUND) |
![]() |
Remove the No. 1, No. 2 and No. 3 PTC heater relays from the engine room No. 2 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| No. 1 PTC heater relay terminal 2 - Body ground | Always | Below 1 Ω |
| No. 2 PTC heater relay terminal 2 - Body ground | Always | Below 1 Ω |
| No. 3 PTC heater relay terminal 2 - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - PTC HEATER RELAY) |
![]() |
Remove the No. 1, No. 2 and No. 3 PTC heater relays from the engine room No. 2 relay block.
Turn the ignition switch on (IG).
When the PTC heater operating conditions are met (engine at idling speed or faster, ambient temperature is 10°C (50°F) or less, engine coolant temperature is 65°C (149°F) or less, set temperature switch is set to MAX HOT), turn the blower switch to the Lo setting.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| No. 1 PTC heater relay terminal 1 - Body ground | Always | 11 to 14 V |
| No. 2 PTC heater relay terminal 1 - Body ground | Always | 11 to 14 V |
| No. 3 PTC heater relay terminal 1 - Body ground | Always | 11 to 14 V |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (BATTERY - PTC HEATER RELAY) |
![]() |
Remove the No. 1, No. 2 and No. 3 PTC heater relays from the engine room No. 2 relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| No. 1 PTC heater relay terminal 5 - Body ground | Always | 11 to 14 V |
| No. 2 PTC heater relay terminal 5 - Body ground | Always | 11 to 14 V |
| No. 3 PTC heater relay terminal 5 - Body ground | Always | 11 to 14 V |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - PTC HEATER) |
![]() |
Remove the No. 1, No. 2 and No. 3 PTC heater relays from the engine room No. 2 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| No. 1 PTC heater relay terminal 3 - D44-2 (B) | Always | Below 1 Ω |
| No. 2 PTC heater relay terminal 3 - D44-3 (B) | Always | Below 1 Ω |
| No. 3 PTC heater relay terminal 3 - D44-1 (B) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 7.CHECK AIR CONDITIONING AMPLIFIER |
![]() |
Remove the air conditioning amplifier with its connectors still connected .
Turn the ignition switch on (IG).
When the PTC heater operating conditions are met (engine at idling speed or faster, ambient temperature is 10°C (50°F) or less, engine coolant temperature is 65°C (149°F) or less, set temperature switch is set to MAX HOT), turn the blower switch to the Lo setting.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D37-3 (PTC1) - Body ground | Always | 11 to 14 V |
| D37-22 (PTC2) - Body ground | Always | 11 to 14 V |
| D37-4 (PTC3) - Body ground | Always | 11 to 14 V |
|
| ||||
| OK | |
| 8.REPLACE PTC HEATER |
Replace the PTC heater
| NEXT | |
| 9.CHECK PTC HEATER (OPERATION) |
Operate the PTC heater to check that functions properly.
|
| ||||
| OK | ||
| ||