Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)

AIR CONDITIONING SYSTEM (for Manual Air Conditioning System) > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using Techstream to read the Data List allows the values or states of switches, sensors, actuators, and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Connect Techstream to the DLC3.

  2. Turn the ignition switch on (IG) and turn Techstream on.

  3. Read the Data List by following the prompts on the tester.

    Data List / Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Ambient Temp Sensor
    Ambient temperature sensor /
    Min.: -23.3°C (-9.94°F)
    Max.: 65.95°C (150.71°F)
    Actual ambient temperature is displayed
    Open in circuit: -23.3°C (-9.94°F)
    Short in circuit: 65.95°C (150.71°F)
    Engine Coolant Temp
    Engine coolant temperature sensor /
    Min.: 1.3°C (34.34°F)
    Max.: 90.55°C (194.99°F)
    Actual engine coolant temperature is displayed
    -
    Blower motor speed Level
    Blower motor speed level /
    Min.: 0, Max.: 31
    Increases in range between 0 and 31 as blower motor speed increases
    -
    Adjusted Ambient Temp
    Adjusted ambient temperature /
    Min.: -30.8°C (-23.44°F)
    Max.: 50.8°C (123.44°F)
    Adjusted ambient temperature is displayed
    -
    Air Mix Sensor Targ Pulse(P)
    Passenger side air mix servo motor target pulse /
    Min.: 0, Max.: 255
    MAX. COLD: 105 (pulse)
    MAX. HOT: 7 (pulse)
    -
    Air Mix Sensor Targ Pulse(D)
    Driver side air outlet servo motor target /
    Min.: 0, Max.: 255
    FACE: 8 (pulse)
    B/L: 30 (pulse)
    FOOT: 67 (pulse)
    FOOT/DEF: 80 (pulse)
    DEF: 97 (pulse)
    -
    Air Inlet Damper Targ Pulse
    Air inlet damper target pulse /
    Min.: 0, Max.: 255
    RECIRCULATION: 7 (pulse)
    FRESH: 28 (pulse)
    -
    Evaporator Fin Temperature
    Evaporator temperature sensor /
    Min.: -29.7°C (-21.46°F)
    Max.: 59.55°C (139.19°F)
    Actual evaporator temperature is displayed
    -
    Regulator Pressure Sensor
    Regulator pressure sensor /
    Min.: 0 kgf/cm2G
    Max.: 38.25 kgf/cm2G
    Actual regulator pressure is displayed
    -
    Regulator Control Current
    Regulator control current /
    Min.: 0 A
    Max.: 0.997 A
    Value changes between 0 A and 0.997 A in accordance with compressor and magnetic clutch operation
    -
    #Codes
    Number of trouble codes /
    Min.: 0, Max.: 255
    Number of DTCs displayed
    -


PERFORM ACTIVE TEST

HINT:
Using Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect Techstream to the DLC3.

  2. Turn the ignition switch on (IG) and turn Techstream on.

  3. Perform the Active Test by following the prompts on the tester.

    Active Test / Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Blower Motor
    Blower motor
    Min.: 0, Max.: 31
    -
    Magnetic Clutch Relay
    Magnetic clutch relay
    OFF, ON
    -
    Defogger Relay (Rear)
    Defogger relay (Rear)
    OFF, ON
    -
    Electric Heater1
    PTC heater 1
    OFF, ON
    -
    Electric Heater2
    PTC heater 2
    OFF, ON
    -
    Electric Heater3
    PTC heater 3
    OFF, ON
    -
    Air Mix Servo Targ Pulse(P)
    Air mix servo motor pulse (P side)
    Min.: 7, Max.: 105
    -
    Air Outlet Servo Targ Pulse(D)
    Air outlet servo motor pulse (D side)
    Min.: 8, Max.: 97
    -
    Air Inlet Damper Targ Pulse(D)
    Air inlet damper target pulse
    Min.: 7, Max.: 28
    -