ENGINE IMMOBILISER SYSTEM (w/o Smart Key System) > TERMINALS OF ECU |
| CHECK TRANSPONDER KEY AMPLIFIER |
Disconnect the D27 transponder key amplifier connector and measure the resistance according to the value(s) in the table below.

| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| D27-7 (AGND) - Body ground | G - Body ground | Ground | Always | Below 1 Ω |
Reconnect the D27 transponder key amplifier connector and measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| D27-1 (VC5) - D27-7 (AGND) | P - G | Power source | No key is in ignition key cylinder | Below 1 V |
| D27-1 (VC5) - D27-7 (AGND) | P - G | Power source | Key is in ignition key cylinder | 4.6 to 5.4 V |
| D27-4 (CODE) - D27-7 (AGND) | R - G | Demodulated signal of key code data | No key is in ignition key cylinder | Below 1 V |
| D27-4 (CODE) - D27-7 (AGND) | R - G | Demodulated signal of key code data | Key is in ignition key cylinder | Waveform 1 |
| D27-5 (TXCT) - D27-7 (AGND) | SB - G | Key code output signal | No key is in ignition key cylinder | Below 1 V |
| D27-5 (TXCT) - D27-7 (AGND) | SB - G | Key code output signal | Key is in ignition key cylinder | Waveform 2 |
Inspect using an oscilloscope.
![]() |
Waveform 1 (Reference)
| Item | Content |
| Tester Connection | D27-4 (CODE) - D27-7 (AGND) |
| Tool Setting | 2 V/DIV., 20 ms./DIV. |
| Condition | Key is in ignition key cylinder |
![]() |
Waveform 2 (Reference)
| Item | Content |
| Tester Connection | D27-5 (TXCT) - D27-7 (AGND) |
| Tool Setting | 2 V/DIV., 10 ms./DIV. |
| Condition | Key is in ignition key cylinder |
| CHECK TRANSPONDER KEY ECU ASSEMBLY |
Disconnect the D41 transponder key ECU connector and measure the resistance and voltage according to the value(s) in the table below.

| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| D41-1 (+B) - D41-16 (GND) | GR - V | Battery | Always | 11 to 14 V |
| D41-2 (IG) - D41-16 (GND) | P - V | Ignition switch signal | Ignition switch OFF | Below 1 V |
| D41-2 (IG) - D41-16 (GND) | P - V | Ignition switch signal | Ignition switch ON | 11 to 14 V |
| D41-3 (KSW) - D41-16 (GND) | O - V | Unlock warning switch signal | No key is in ignition key cylinder | 10 kΩ or higher |
| D41-3 (KSW) - D41-16 (GND) | O - V | Unlock warning switch signal | Key is in ignition key cylinder | Below 1 Ω |
| D41-16 (GND) - Body ground | V - Body ground | Ground | Always | Below 1 Ω |
Reconnect the D41 transponder key ECU connector and measure the resistance and voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| D41-3 (KSW) - D41-16 (GND) | O - V | Unlock warning switch signal | No key is in ignition key cylinder | 11 to 14 V |
| D41-3 (KSW) - D41-16 (GND) | O - V | Unlock warning switch signal | Key is in ignition key cylinder | Below 1 V |
| D41-4 (TXCT) - D41-5 (AGND) | SB - G | Transponder key amplifier communication signal | No key is in ignition key cylinder | Below 1 V |
| D41-4 (TXCT) - D41-5 (AGND) | SB - G | Transponder key amplifier communication signal | Key is in ignition key cylinder | Waveform 1 |
| D41-5 (AGND) - Body ground | G - Body ground | Ground | Always | Below 1 Ω |
| D41-7 (CTY) - D41-16 (GND) | LG - V | Door courtesy signal | Switch pushed | 11 to 14 V |
| D41-7 (CTY) - D41-16 (GND) | LG - V | Door courtesy signal | Switch free | Below 1 V |
| D41-8 (IND) - D41-16 (GND) | Y - V | Security indicator light signal | Security indicator light is on | 11 to 14 V |
| D41-8 (IND) - D41-16 (GND) | Y - V | Security indicator light signal | Security indicator light is off | Below 1 V |
| D41-9 (D) - D41-16 (GND) | B - V | Diagnostic tester communication | Without communication | Below 1 V |
| D41-9 (D) - D41-16 (GND) | B - V | Diagnostic tester communication | During communication | Pulse generation |
| D41-12 (EFII) - D41-16 (GND) | BR - V | ECM input signal | Ignition switch OFF | Below 1 V |
| D41-12 (EFII) - D41-16 (GND) | BR - V | ECM input signal | Ignition switch ON | Waveform 2 |
| D41-13 (EFIO) - D41-16 (GND) | L - V | ECM output signal | Ignition switch OFF | Below 1 V |
| D41-13 (EFIO) - D41-16 (GND) | L - V | ECM output signal | Ignition switch ON | Waveform 3 |
| D41-14 (VC5) - D41-5 (AGND) | P - G | Power source | No key is in ignition key cylinder | Below 1 V |
| D41-14 (VC5) - D41-5 (AGND) | P - G | Power source | Key is in ignition key cylinder | 4.6 to 5.4 V |
| D41-15 (CODE) - D41-5 (AGND) | R - G | Transponder key amplifier communication signal | No key is in ignition key cylinder | Below 1 V |
| D41-15 (CODE) - D41-5 (AGND) | R - G | Transponder key amplifier communication signal | Key is in ignition key cylinder | Waveform 4 |
Inspect using an oscilloscope.
![]() |
Waveform 1 (Reference)
| Item | Content |
| Tester Connection | D41-4 (TXCT) - D41-5 (AGND) |
| Tool Setting | 2 V/DIV., 10 ms./DIV. |
| Condition | Key is in ignition key cylinder |
![]() |
Waveform 2 (Reference)
| Item | Content |
| Tester Connection | D41-12 (EFII) - D41-16 (GND) |
| Tool Setting | 2 V/DIV., 1 s./DIV. |
| Condition | Ignition switch ON |
![]() |
Waveform 3 (Reference)
| Item | Content |
| Tester Connection | D41-13 (EFIO) - D41-16 (GND) |
| Tool Setting | 2 V/DIV., 1 s./DIV. |
| Condition | Ignition switch ON |
![]() |
Waveform 4 (Reference)
| Item | Content |
| Tester Connection | D41-15 (CODE) - D41-5 (AGND) |
| Tool Setting | 2 V/DIV., 20 ms./DIV. |
| Condition | Key is in ignition key cylinder |
| CHECK ECM |
Disconnect the B3 ECM connector and measure the resistance according to the value(s) in the table below.

| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| B3-1 (E1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the B3 ECM connector. Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| D36-15 (IMO) - B3-1 (E1) | BR - W-B | Transponder key ECU output signal | Ignition switch OFF | Below 1 V |
| D36-15 (IMO) - B3-1 (E1) | BR - W-B | Transponder key ECU output signal | Ignition switch ON | Waveform 1 |
| D36-16 (IMI) - B3-1 (E1) | L - W-B | Transponder key ECU input signal | Ignition switch OFF | Below 1 V |
| D36-16 (IMI) - B3-1 (E1) | L - W-B | Transponder key ECU input signal | Ignition switch ON | Waveform 2 |
Inspect using an oscilloscope.
![]() |
Waveform 1 (Reference)
| Item | Content |
| Tester Connection | D36-15 (IMO) - B3-1 (E1) |
| Tool Setting | 2 V/DIV., 1 s./DIV. |
| Condition | Ignition switch ON |
![]() |
Waveform 2 (Reference)
| Item | Content |
| Tester Connection | D36-16 (IMI) - B3-1 (E1) |
| Tool Setting | 2 V/DIV., 1 s./DIV. |
| Condition | Ignition switch ON |