Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › PTC HEATER ASSEMBLY

PTC HEATER ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL QUICK HEATER ASSEMBLY


    E151055
  1. Install the quick heater assembly with the 3 screws as shown in the illustration.

  1. Connect the 2 connectors.



2. INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY


    E151056
  1. Engage the 3 claws and install the No. 3 air duct sub-assembly as shown in the illustration.



3. INSTALL FRONT NO. 2 CONSOLE BOX INSERT


    B168374
  1. Engage the claw and 2 guides.

  1. Install the front No. 2 console box insert with the 3 screws <F> and clip.



4. INSTALL CONSOLE BOX ASSEMBLY


    B175149
  1. Engage the 6 claws.

  1. Connect the connector.



    B181135
  1. Install the console box assembly with the 4 bolts and 2 screws.



5. INSTALL LOWER REAR CONSOLE BOX
  1. Install the lower rear console box.



6. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    B168372
  1. Connect the connector.

  1. Engage the 4 claws and 4 clips, and install the upper console panel sub-assembly.



7. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
  1. Connect each connector and clamp.



    B168370
  1. Engage the 4 claws and 3 clips.

  1. Install the lower instrument panel sub-assembly with the 2 bolts <B> and 3 screws <F>.



8. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    B173000
  1. Engage the 2 guides.

  1. Engage the 3 claws and install the No. 2 instrument panel under cover sub-assembly.



9. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.



10. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.



11. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Navigation System)
  1. Connect each connector.



    E150552
  1. Engage the 4 clips.



    E150551
  1. Install the radio receiver assembly with bracket with the 4 bolts.



12. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)
  1. Connect each connector.



    E150545
  1. Engage the 4 clips.



    E150544
  1. Install the navigation receiver assembly with bracket with the 4 bolts.



13. INSTALL HEATER CONTROL AND ACCESSORY ASSEMBLY (for Manual Air Conditioning System)
  1. Connect the connector.



    E150368
  1. Engage the 4 clips and install the heater control and accessory assembly.



14. INSTALL AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)
  1. Connect the connector.



    E150367
  1. Engage the 4 clips and install the air conditioning control assembly.



15. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Smart Key System)


    B184679E01
  1. Apply protective tape to the areas shown in the illustration.

  1. Connect each connector.

  1. Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.

    NOTICE:
    Do not the damage the instrument panel safety pad assembly and lower instrument panel finish panel sub-assembly.



16. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Key System)


    B184681E01
  1. Apply protective tape to the areas shown in the illustration.

  1. Connect each connector.

  1. Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.

    NOTICE:
    Do not the damage the instrument panel safety pad assembly and lower instrument panel finish panel sub-assembly.



17. INSTALL CENTER INSTRUMENT PANEL REGISTER ASSEMBLY


    B168369
  1. Engage the 2 claws and 5 clips, and install the center instrument panel register assembly.