Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › PTC HEATER ASSEMBLY

PTC HEATER ASSEMBLY > REMOVAL

for Preparation Click here



1. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY


    B168368E01
  1. Apply protective tape to the areas shown in the illustration.

  1. Using a moulding remover, disengage the 2 claws and 5 clips, and then remove the center instrument panel register assembly as shown in the illustration.



2. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Smart Key System)


    B184678E01
  1. Apply protective tape to the areas shown in the illustration.

  1. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

    NOTICE:
    Do not pull on the small storage compartment lid. Doing so may cause damage.

  1. Disconnect each connector and remove the center instrument cluster finish panel assembly.



3. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Key System)


    B184680E01
  1. Apply protective tape to the areas shown in the illustration.

  1. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

    NOTICE:
    Do not pull on the small storage compartment lid. Doing so may cause damage.

  1. Disconnect each connector and remove the center instrument cluster finish panel assembly.



4. REMOVE HEATER CONTROL AND ACCESSORY ASSEMBLY (for Manual Air Conditioning System)


    E150368
  1. Disengage the 4 clips and remove the heater control and accessory assembly.

  1. Disconnect the connector.



5. REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)


    E150367
  1. Disengage the 4 clips and remove the air conditioning control assembly.

  1. Disconnect the connector.



6. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Navigation System)


    E150551
  1. Remove the 4 bolts.



    E150552
  1. Pull the radio receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.

  1. Disconnect each connector and remove the radio receiver assembly with bracket.



7. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)


    E150544
  1. Remove the 4 bolts.



    E150545
  1. Pull the navigation receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.

  1. Disconnect each connector and remove the navigation receiver assembly with bracket.



8. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.



9. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.



10. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    B172999
  1. Disengage the 3 claws.

  1. Disengage the 2 guides and remove the No. 2 instrument panel under cover sub-assembly.



11. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    B168370
  1. Remove the 2 bolts <B> and 3 screws <F>.

  1. Disengage the 4 claws and 3 clips.

  1. Disconnect each connector and clamp, and remove the lower instrument panel sub-assembly.



12. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    B168372
  1. Disengage the 4 claws and 4 clips.

  1. Disconnect the connector and remove the upper console panel sub-assembly.



13. REMOVE LOWER REAR CONSOLE BOX
  1. Remove the lower rear console box.



14. REMOVE CONSOLE BOX ASSEMBLY


    B181135
  1. Remove the 4 bolts and 2 screws.



    B175149
  1. Disconnect the connector.

  1. Disengage the 6 claws, and remove the console box assembly.



15. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


    B168374
  1. Using a clip remover, remove the clip.

  1. Remove the 3 screws <F>.

  1. Disengage the claw and 2 guides, and then remove the front No. 2 console box insert.



16. REMOVE NO. 3 AIR DUCT SUB-ASSEMBLY


    E151057
  1. Disengage the 3 claws and remove the No. 3 air duct sub-assembly as shown in the illustration.



17. REMOVE QUICK HEATER ASSEMBLY


    E151054
  1. Disconnect the 2 connectors.

  1. Remove the 3 screws and the quick heater assembly as shown in the illustration.