Home › ENGINE › 2GR-FE COOLING › WATER PUMP

WATER PUMP > INSTALLATION

for Preparation Click here



1. INSTALL WATER PUMP ASSEMBLY


    A128115E03
  1. Install a new water pump gasket and the water pump assembly with the 16 bolts.

    Torque:
    Bolt A:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }
    Bolts B and C:
    11 N*m{ 112 kgf*cm , 8 in.*lbf }

    NOTICE:
    1. Make sure that there is no oil on the threads of bolts A.
    2. Be sure to replace 2 bolts C with new ones or reuse them after applying adhesive 1344.

      Adhesive:
      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



2. INSTALL WATER INLET HOUSING


    A128122
  1. Install a new water inlet housing gasket and water outlet pipe O-ring.



    A133375E04
  1. Install the water inlet housing with the 2 bolts and nut.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Be careful not to allow the O-ring to get caught between the parts.

  1. Connect the water hose.



3. INSTALL WATER PUMP PULLEY


    A128112E01
  1. Temporarily install the water pump pulley with the 4 bolts.

  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Tighten the 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }



4. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY


    A161449
  1. Install the V-ribbed belt tensioner assembly with the 5 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



5. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY


    A195782E01
  1. Install the idler pulley cover plate, No. 2 idler pulley cover plate and No. 2 idler pulley sub-assembly with the bolt.

    Torque:
    54 N*m{ 550 kgf*cm , 40 ft.*lbf }

    HINT:
    Plate diameter:
    Idler pulley cover plate: 33.6 mm (1.32 in.)
    No. 2 idler pulley cover plate: 37.8 mm (1.49 in.)



6. INSTALL GENERATOR ASSEMBLY


    A170743
  1. Install the wire harness clamp stay with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    A170150
  1. Connect the generator bracket with the wire harness clamp.



    A170146
  1. Install generator assembly with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



    A170145
  1. Temporally install the 2 bolts.



    A170145
  1. Fully tighten the 2 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    A170144
  1. Connect the generator connector to the generator assembly.

  1. Install the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.

  1. Connect the 3 wire harness clamps.

  1. Connect the magnetic clutch connector to the compressor and magnetic clutch.



7. INSTALL ENGINE HANGERS


    A129635E01
  1. Install the 2 engine hangers with the 4 bolts as shown in the illustration.

    Part No.:
    No. 1 Engine hanger 12281-31120
    No. 2 Engine hanger 12282-31100
    Bolts 91671-10825

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }

  1. Attach the engine sling device and hang the engine with the chain block.



8. REMOVE ENGINE STAND


9. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

HINT:
Click here.