Home › DRIVE LINE › DRIVE SHAFT › FRONT DRIVE SHAFT

FRONT DRIVE SHAFT > DISASSEMBLY

for Preparation Click here



1. REMOVE FRONT DRIVE SHAFT HOLE SNAP RING


    C057543E04
  1. Using a screwdriver, remove the front drive shaft hole snap ring.



2. REMOVE NO. 2 FRONT AXLE INBOARD JOINT BOOT CLAMP


    C108564
  1. Using pliers, remove the No. 2 front axle inboard joint boot clamp as shown in the illustration.



3. REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP
  1. Remove the front axle inboard joint boot clamp.

    HINT:
    Perform the same procedures as for the No. 2 front axle inboard joint boot clamp.



4. SEPARATE FRONT AXLE INBOARD JOINT BOOT
  1. Separate the front axle inboard joint boot from the inboard joint assembly.



5. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY
  1. Remove the grease from the inboard joint assembly.



    F045461E12
  1. Put matchmarks on the inboard joint assembly and outboard joint shaft.

    NOTICE:
    Do not use a punch for the marks.

  1. Remove the inboard joint assembly from the outboard joint shaft.



    F045046
  1. Using a snap ring expander, remove the shaft snap ring.



    C141145E05
  1. Put matchmarks on the outboard joint shaft and tripod joint.

    NOTICE:
    Do not use a punch for the marks.

  1. Using a brass bar and a hammer, remove the tripod joint from the outboard joint shaft.

    NOTICE:
    Do not tap the roller.



6. REMOVE FRONT AXLE INBOARD JOINT BOOT
  1. Remove the inboard joint boot from the outboard joint shaft.



7. REMOVE FRONT DRIVE SHAFT DAMPER


    C108273
  1. Using pliers, remove the drive shaft damper clamp as shown in the illustration.

  1. Remove the drive shaft damper.



8. REMOVE NO. 2 FRONT AXLE OUTBOARD JOINT BOOT CLAMP


    C081167E02
  1. Using pliers, remove the No. 2 front axle outboard joint boot clamp as shown in the illustration.



9. REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP
  1. Remove the front axle outboard joint boot clamp.

    HINT:
    Perform the same procedures as for the No. 2 front axle outboard joint boot clamp.



10. REMOVE FRONT AXLE OUTBOARD JOINT BOOT
  1. Remove the outboard joint boot from the outboard joint shaft.

  1. Remove the grease from the outboard joint.



11. REMOVE FRONT DRIVE SHAFT DUST COVER LH


    F040647E07
  1. Using SST and a press, remove the drive shaft dust cover LH.

    SST
    09950-00020  

    NOTICE:
    Be careful not to drop the inboard joint assembly.



12. REMOVE FRONT DRIVE SHAFT DUST COVER RH (for 2WD RH Side)


    C067101E02
  1. Using a press, remove the drive shaft dust cover RH.



13. REMOVE FRONT DRIVE SHAFT DUST COVER RH (for 4WD RH Side)

HINT:
Perform the same procedure as for the LH side.



14. REMOVE FRONT DRIVE SHAFT DUST COVER (for 2WD RH Side)


    F040208E03
  1. Using SST and a press, remove the drive shaft dust cover.

    SST
    09950-00020  



15. REMOVE SIDE GEAR SHAFT HOLDER BEARING (for 2WD RH Side)


    C092033E04
  1. Using a snap ring expander, remove the drive shaft hole snap ring.



    F040210E04
  1. Using SST and a press, remove the bearing.

    SST
    09527-10011  

  1. Remove the bearing bracket hole snap ring.

    NOTICE:
    Be careful not to drop the inboard joint assembly.