VEHICLE STABILITY CONTROL SYSTEM > TERMINALS OF ECU |
| TERMINALS OF ECU |

| Terminal No. (Symbols) | Terminal Description |
| 1 (GND1) | Skid control ECU ground |
| 2 (STP) | Stop light switch input |
| 4 (RL-) | Rear wheel speed LH (-) signal input |
| 5 (RL+) | Rear wheel speed LH (+) power supply output |
| 6 (FR-) | Front wheel speed RH (-) signal input |
| 7 (FR+) | Front wheel speed RH (+) power supply output |
| 11 (SP1) | Speed signal output for speedometer |
| 12 (+BS) | Solenoid relay power supply |
| 13 (GND2) | Pump motor ground |
| 14 (CANL) | CAN communication line L |
| 16 (RR-) | Rear wheel speed RH (-) signal input |
| 17 (RR+) | Rear wheel speed RH (+) power supply output |
| 18 (FL-) | Front wheel speed LH (-) signal input |
| 19 (FL+) | Front wheel speed LH (+) power supply output |
| 21 (BZ) | Skid control buzzer output |
| 22 (STP2) | Stop light control relay input |
| 24 (+BM) | Motor relay power supply |
| 25 (CANH) | CAN communication line H |
| 26 (HDCS) (*1) | Downhill assist control switch input |
| 27 (FSW+) | Brake pedal load sensing switch input |
| 29 (PKB) | Parking brake switch input |
| 30 (CSW) | VSC OFF switch input |
| 31 (STPO) | Stop light control relay output |
| 33 (TS) | Sensor check input |
| 34 (IG1) | ECU power supply |
| TERMINAL INSPECTION |
Disconnect the connectors and measure the voltage or resistance on the wire harness side.

| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| A24-1 (GND1) - Body ground | W-B - Body ground | Skid control ECU ground | Always | Below 1 Ω |
| A24-2 (STP) - Body ground | L - Body ground | Stop light switch input | Stop light switch ON → OFF (Brake pedal depressed → released) | 8 to 14 V → Below 1.5 V |
| A24-12 (+BS) - Body ground | R - Body ground | Solenoid relay power supply | Always | 11 to 14 V |
| A24-13 (GND2) - Body ground | W-B - Body ground | Pump motor ground | Always | Below 1 Ω |
| A24-21 (BZ) - Body ground | Y - Body ground | Skid control buzzer output | Ignition switch on (IG), buzzer not sounding | 6 to 10 V |
| A24-22 (STP2) - Body ground | L - Body ground | Stop light control relay input | Stop light switch ON → OFF (Brake pedal depressed → released) | 8 to 14 V → Below 1.5 V |
| A24-24 (+BM) - Body ground | B - Body ground | Motor relay power supply | Always | 11 to 14 V |
| A24-26 (HDCS) (*1) - Body ground | W - Body ground | Downhill assist control switch input | Downhill assist control switch is pushed in → released | Below 1 Ω → 10 kΩ or higher |
| A24-27 (FSW+) - Body ground | GR - Body ground | Brake pedal load sensing switch input | Brake pedal load sensing switch OFF → ON (Brake pedal depressed → released) | 950 to 1050 Ω → 203 to 223 Ω |
| A24-29 (PKB) - Body ground | BR - Body ground | Parking brake switch input | Ignition switch on (IG), parking brake switch OFF → ON | Below 1 Ω → 10 kΩ or higher |
| A24-30 (CSW) - Body ground | G - Body ground | VSC OFF switch input | VSC OFF switch held ON → OFF (Released) | Below 25 Ω → 10 kΩ or higher |
| A24-31 (STPO) - Body ground | P - Body ground | Stop light control relay output | Ignition switch on (IG) | 11 to 14 V |
| A24-34 (IG1) - Body ground | O - Body ground | ECU power supply | Ignition switch on (IG) | 11 to 14 V |