Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0111    Intake Air Temperature Sensor Gradient Too High

for Preparation Click here


DESCRIPTION

A067628E13
  1. The intake air temperature sensor, mounted on the mass air flow meter, monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature becomes low, the resistance of the thermistor increases. When the temperature becomes high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (see Fig. 1).
  2. The intake air temperature sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.
  3. Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes according to changes in the intake air temperature, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

DTC No.
DTC Detection Condition
Trouble Area
P0111
  1. The intake air temperature rise becomes larger, from the previous trip warm-up to the following trip.(2 trip detection logic)
  2. When the change in the intake air temperature after engine start is less than the threshold value.
Mass air flow meter assembly

MONITOR DESCRIPTION

The ECM performs OBD II monitoring based on the values from the intake air temperature sensor. If there is no change in the sensor value, the ECM will not be able to perform OBD II monitoring or will misdiagnose that there is a malfunction in the sensor. The ECM detects the stuck intake air temperature sensor value by performing monitoring after the ignition switch is turned off or the ignition is started (short soak or long soak).

MONITOR STRATEGY


Related DTCs
P0111: Intake air temperature sensor rationality (After engine stop)
P0111: Intake air temperature sensor rationality (After cold engine start)
Required Sensors / Components (Main)
Intake Air Temperature (IAT) sensor
Required Sensors / Components (Sub)
-
Frequency of Operation
Once per driving cycle
Duration
5 hours
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
The monitor will run whenever these DTCs are not present
None

After engine stop: 
Time after engine start
10 seconds or more
Battery voltage
10.5 V or more
Engine coolant temperature sensor
OK
Engine coolant temperature change since engine stopped
Less than 180°C (356°F)
Engine coolant temperature before engine stop
70°C (158°F) or more
Time that mass air flow is low before engine stop
70 minutes
Accumulated mass air flow amount before engine stop
1720 g or more
Key-off duration
30 minutes

After cold engine start: 
Key-off duration
5 hours
Time after engine start
10 seconds or more
Engine coolant temperature sensor
OK
Engine coolant temperature
70°C (158°F) or more
Accumulated mass air flow amount
1720 g or more
One of the following conditions 1 or 2 is met:
-
1. Duration while engine load is low
120 seconds or more
2. Duration while engine load is high
10 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


After engine stop: 
Intake air temperature change
Less than 1°C (33.8°F)

After cold engine start: 
Intake air temperature change
Less than 1°C (33.8°F)

WIRING DIAGRAM

Refer to DTC P0110 .

INSPECTION PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0111)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P0111 and other DTCs
    A
    P0111
    B

    HINT:
    If any DTCs other than P0111 are output, troubleshoot those DTCs first.



B
REPLACE MASS AIR FLOW METER (Click here)
A

GO TO DTC CHART (Click here)