DTC B1820/55 Short in Front Driver Side - Side Squib Circuit |
DTC B1821/55 Open in Front Driver Side - Side Squib Circuit |
DTC B1822/55 Short to GND in Front Driver Side - Side Squib Circuit |
DTC B1823/55 Short to B+ in Front Driver Side - Side Squib Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1820/55 |
|
|
| B1821/55 |
|
|
| B1822/55 |
|
|
| B1823/55 |
|
|

| 1.CHECK CONNECTORS |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the front seat side airbag assembly LH and center airbag sensor assembly.
Disconnect the connectors from the front seat side airbag assembly LH and center airbag sensor assembly.
Check that the connectors of the terminals are not damaged.
|
| ||||
| OK | |
| 2.CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY LH (FRONT DRIVER SIDE - SIDE SQUIB) |
![]() |
Connect the connector to the center airbag sensor assembly.
Connect SST (resistance 2.1 Ω) to connector C.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| OK | A |
| NG (for Manual seat) | B |
| NG (for Power seat) | C |
|
| ||||
|
| ||||
| A | |
| 3.CHECK FLOOR WIRE NO. 2 (FRONT DRIVER SIDE - SIDE SQUIB CIRCUIT) |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect SST from connector C.
Disconnect the floor wire No. 2 from the center airbag sensor assembly.
Check for a short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O5-1 (SFL+) - Body ground | Ignition switch on (IG) | Below 1 V |
| O5-2 (SFL-) - Body ground | Ignition switch on (IG) | Below 1 V |
Check for an open in the circuit.
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O5-1 (SFL+) - O5-2 (SFL-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O5-1 (SFL+) - Body ground | Always | 1 MΩ or higher |
| O5-2 (SFL-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O5-1 (SFL+) - O5-2 (SFL-) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 4.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Restore the released activation prevention mechanism of connector B to the original condition.
Connect the connectors to the front seat side airbag assembly LH and the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||