Home › SECURITIES › THEFT DETERRENT › THEFT DETERRENT SYSTEM (w/o Smart Key System)

THEFT DETERRENT SYSTEM (w/o Smart Key System) > TERMINALS OF ECU



CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)


  1. Disconnect the main body ECU (instrument panel junction block) connectors.


    B150879E09

  2. Measure the resistance and voltage between each terminal of the wire harness side connectors and body ground.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D7-5 (RCTY)*1 - Body ground
    GR - Body ground
    Rear courtesy light switch RH input
    Rear door RH CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    D7-7 (RCTY)*2 - Body ground
    GR - Body ground
    Rear courtesy light switch RH input
    Rear door RH CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    D7-21 (PCTY) - Body ground
    SB - Body ground
    Passenger side courtesy light switch input
    Passenger side door CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    D7-25 (BCTY) - Body ground
    L - Body ground
    Back door courtesy light switch input
    Back door CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    D8-16 (HCTY) - Body ground
    R - Body ground
    Engine hood courtesy switch
    Engine hood CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    D8-24 (DCTY) - Body ground
    G - Body ground
    Driver side door courtesy light switch input
    Driver side door CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    D8-20 (GCTY)*3 - Body ground
    P - Body ground
    Glass hatch courtesy switch
    Glass hatch CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    D10-5 (KSW) - Body ground
    GR - Body ground
    Unlock warning switch input
    No key in ignition key cylinder (OFF) → Key inserted (ON)
    10 kΩ or higher → Below 1 Ω
    1A-1 (ACC) - Body ground
    B - Body ground
    Ignition power supply (ACC signal)
    Ignition switch ACC → OFF
    11 to 14 V → Below 1 V
    1A-1 (IG) - Body ground
    B - Body ground
    Ignition power supply (IG signal)
    Ignition switch ON → OFF
    11 to 14 V → Below 1 V
    1D-16 (ALTB) - Body ground
    W - Body ground
    +B (power system alternator system) power supply
    Always
    11 to 14 V
    1F-10 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1D-10 (BECU) - Body ground
    W - Body ground
    +B power supply
    Always
    11 to 14 V
    1M-9 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1O-7 (LCTY) - Body ground
    B - Body ground
    Rear courtesy light switch LH input
    Rear door LH CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω

    HINT:
    1. *1: w/o Power Back Door System
    2. *2: w/ Power Back Door System
    3. *3: w/ Glass Hatch Opener System
    4. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the main body ECU (instrument panel junction block) connectors.

  4. Measure the voltage between each terminal of the wire harness side connectors and body ground.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D9-4 (HAZ) - Body ground
    O - Body ground
    Turn signal flasher relay signal
    System is in alarm sounding state
    Below 1 V
    D10-4 (IND) - Body ground
    B - Body ground
    Security indicator output
    Security indicator is on
    (It lights up only in arming preparation state or alarm sounding state. It flashes when immobiliser is operating.)
    3 to 6 V
    D10-6 (SH) - Body ground
    W - Body ground
    Security horn drive
    Security horn is sounding
    (Theft deterrent system is in alarm sounding state)
    Pulse generation
    (Below 1 V ← → 12 V)
    1D-11 (HORN) - Body ground
    GR - Body ground
    Vehicle horn drive
    Vehicle horn is sounding
    (Theft deterrent system is in alarm sounding state)
    Pulse generation
    (Below 1 V ← → 12 V)
    If the result is not as specified, the main body ECU (instrument panel junction block) may have a malfunction.