Home › DRIVE LINE › MF2A TRANSFER › TRANSFER ASSEMBLY

TRANSFER ASSEMBLY > DISASSEMBLY

for Preparation Click here



1. REMOVE TRANSFER COVER GASKET


    C082798
  1. Remove the transfer cover gasket from the transfer assembly.



2. REMOVE TRANSFER CASE BREATHER PLUG


    C094714
  1. Using a screwdriver and a hammer, remove the transfer case breather plug from the No. 1 transfer case cover.

    NOTICE:
    Be careful not to damage the contact surface of the No. 1 transfer case cover.



3. REMOVE NO. 1 TRANSFER CASE COVER


    C083507
  1. Remove the 8 bolts.



    C050303
  1. Using a brass bar and a hammer, remove the No. 1 transfer case cover from the transfer case.

    NOTICE:
    Be careful not to damage the contact surfaces of the case and cover.



4. REMOVE BREATHER OIL DEFLECTOR


    C067665
  1. Remove the bolt and breather oil deflector from the No. 1 transfer case cover.



5. REMOVE TRANSFER DYNAMIC DAMPER


    C082802
  1. Remove the 3 bolts and the transfer dynamic damper from the transfer extension housing sub-assembly.



6. REMOVE TRANSFER CASE STRAIGHT PIN
  1. Remove the 4 transfer case straight pins from the transfer case.



7. REMOVE TRANSFER AND TRANSAXLE SETTING STUD BOLT
  1. Remove the 4 transfer and transaxle setting stud bolts.



8. FIX TRANSFER ASSEMBLY
  1. Fix the transfer assembly to the overhaul attachment.



9. REMOVE TRANSFER EXTENSION HOUSING DUST DEFLECTOR


    C082788
  1. Using a plastic hammer, remove the transfer extension housing dust deflector from the transfer extension housing sub-assembly.



10. REMOVE TRANSFER EXTENSION HOUSING TYPE T OIL SEAL


    C082978E02
  1. Using SST, remove the transfer extension housing type T oil seal from the transfer extension housing.

    SST
    09308-00010  

    NOTICE:
    Be careful not to damage the oil-seal-fitted surface of the housing and the inside surface of the bush.



11. REMOVE TRANSFER EXTENSION HOUSING SUB-ASSEMBLY


    C082790
  1. Remove the 4 bolts.



    C082791
  1. Using a plastic hammer, remove the transfer extension housing sub-assembly from the transfer case.



12. INSPECT PRELOAD


    C083635E10
  1. Using SST and a torque wrench, check the initial torque with the backlash range.

    SST
    09326-20011  

    Torque:
    0.9 to 1.4 N*m{ 9 to 14 kgf*cm , 8.0 to 12.4 in.*lbf }

    HINT:
    Use a torque wrench with a fulcrum length of 160 mm (6.30 in.).

  1. Using SST and a torque wrench, check the initial torque while the driven pinion is in contact with the ring gear face.

    SST
    09326-20011  

    Torque:
    Preload:
    1.07 to 1.68 N*m{ 10.9 to 17.1 kgf*cm , 9.5 to 14.9 in.*lbf }

    HINT:
    Use a torque wrench with a fulcrum length of 160 mm (6.30 in.).



13. REMOVE CTR DIFFERENTIAL LOCK SLEEVE


    C083637
  1. Using snap ring pliers, remove the shaft snap ring.



    C083638E02
  1. Using SST, remove the CTR differential lock sleeve.

    SST
    09308-00010  



14. REMOVE O-RING


    C050311
  1. Using a screwdriver with the tip protected by vinyl tape, remove the O-ring from the CTR differential lock sleeve.

    NOTICE:
    Be careful not to damage the lock sleeve's groove for the O-ring.



15. REMOVE TRANSFER CASE OIL SEAL


    C083630E03
  1. Using SST, remove the transfer case oil seal from the case.

    SST
    09308-00010  

    NOTICE:
    Be careful not to damage the oil-seal-fitted surface of the case.



16. REMOVE TRANSFER RH BEARING RETAINER OIL SEAL


    C082980E02
  1. Using SST, remove the transfer RH bearing retainer oil seal from the transfer RH bearing retainer sub-assembly.

    SST
    09308-00010  

    NOTICE:
    Be careful not to damage the oil-seal-fitted surface of the retainer.



17. REMOVE TRANSFER RH BEARING RETAINER SUB-ASSEMBLY


    C083509
  1. Remove the 7 bolts from the transfer RH bearing retainer sub-assembly.



    C149592E01
  1. Using SST, make a clearance between the transfer RH bearing retainer sub-assembly and the transfer case.

    SST
    09950-00020  

  1. Remove SST.



    C082981E06
  1. Using SST, remove the transfer RH bearing retainer sub-assembly from the transfer case.

    SST
    09520-10021  



18. REMOVE O-RING


    C050313
  1. Using a screwdriver with the tip protected by vinyl tape, remove the 2 O-rings from the transfer RH bearing retainer sub-assembly.

    NOTICE:
    Be careful not to damage the retainer's grooves for the O-rings.



19. REMOVE CENTER DIFFERENTIAL CASE TAPERED ROLLER BEARING


    C083639E02
  1. Fix the transfer RH bearing retainer sub-assembly in a vise.

  1. Using SST, remove the center differential case tapered roller bearing RH outer race, No. 2 transfer ring gear mounting case washer and No. 2 transfer RH bearing retainer oil seal from the transfer RH bearing retainer sub-assembly.

    SST
    09308-00010  

    NOTICE:
    Be careful not to damage the oil-seal-fitted surface of the transfer RH bearing retainer sub-assembly.



20. REMOVE SIDE GEAR SHAFT HOLDER BEARING


    C083640
  1. Using snap ring pliers, remove the side gear shaft holder hole snap ring.

  1. Remove the side gear shaft holder bearing from the transfer RH bearing retainer sub-assembly.



21. REMOVE TRANSFER RING GEAR MOUNTING CASE


    C067673
  1. Remove the transfer ring gear mounting case from the transfer case.



22. REMOVE CENTER DIFFERENTIAL CASE TAPERED ROLLER BEARING
SST
09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60010   (09951-00430)


    C083641E02
  1. Using SST, remove the inner race of the center differential case tapered roller bearing from the transfer ring gear mounting case.

    NOTICE:
    Apply grease to the screw thread and tip of SST before use.



    C083642E02
  1. When the roller comes off due to deformation of the gauge, completely remove the roller and remaining inner races of the center differential case tapered roller bearing from the transfer ring gear mounting case.

    SST
    09950-00020  
    09950-00030  
    09950-60010   (09951-00430)

    NOTICE:
    Apply grease to the screw thread and tip of SST before use.



    C083643E02
  1. Using SST, remove the inner race of the center differential case tapered roller bearing from the transfer ring gear mounting case.

    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00360)

    NOTICE:
    Apply grease to the screw thread and tip of SST before use.



    C083644E02
  1. When the roller comes off due to deformation of the gauge, completely remove the roller and remaining inner races of the center differential case tapered roller bearing from the transfer ring gear mounting case.

    SST
    09950-00020  
    09950-00030  
    09950-60010   (09951-00360)

    NOTICE:
    Apply grease to the screw thread and tip of SST before use.



23. REMOVE RING GEAR


    C083645E03
  1. Put matchmarks on the transfer ring gear mounting case and the ring gear.

  1. Remove the 12 bolts.



    C067677
  1. Using a plastic hammer, remove the ring gear by tapping around its periphery.

    NOTICE:
    Do not damage the teeth of the ring gear.



24. REMOVE TRANSFER GEAR NUT


    C082795E02
  1. Using SST and a hammer, unstake the transfer gear nut.

    SST
    09930-00010  



    C082984E02
  1. Using SST, remove the transfer gear nut.

    SST
    09326-20011  
    09556-16030  



    C082796
  1. Using a press, remove the driven pinion, transfer driven pinion rear bearing inner race and transfer pinion bearing spacer.

    NOTICE:
    1. Put shop cloths around the transfer case to help prevent the driven pinion from dropping out of the bearing.
    2. Place something like wooden blocks under the case to keep its level.



25. REMOVE TRANSFER DRIVEN PINION FRONT BEARING


    C083646E02
  1. Using SST and a press, remove the transfer driven pinion front bearing inner race from the driven pinion.

    SST
    09950-00020  



26. REMOVE CENTER DIFFERENTIAL CASE TAPERED ROLLER BEARING


    C050329
  1. Using a brass bar and a hammer, lightly strike the center differential case tapered roller bearing LH outer race at 2 positions to remove it from the transfer case.



27. REMOVE TRANSFER OUTPUT SHAFT WASHER
  1. Remove the ring gear mounting case plate washer from the transfer case.



28. REMOVE CENTER DIFFERENTIAL CASE TAPERED ROLLER BEARING


    C082781
  1. Using a brass bar and a hammer, lightly strike the transfer driven pinion front bearing outer race at 2 points to remove it from the transfer case.



29. REMOVE RING GEAR MOUNTING CASE PLATE WASHER
  1. Remove the transfer output washer from the transfer case.



30. REMOVE TRANSFER DRIVEN PINION REAR BEARING


    C050331
  1. Using a brass bar and a hammer, lightly strike the transfer driven pinion rear bearing outer race at 2 points to remove it from the transfer case.