REAR DIFFERENTIAL CARRIER ASSEMBLY > DISASSEMBLY |
| 1. REMOVE REAR DIFFERENTIAL CARRIER COVER |
![]() |
Remove the 8 bolts from the rear differential carrier cover.
Using a brass bar and a hammer, separate the rear differential carrier cover from rear differential carrier assembly.
| 2. REMOVE REAR DIFFERENTIAL BREATHER PLUG |
![]() |
Remove the rear differential breather plug from the rear differential carrier cover.
| 3. SECURE REAR DIFFERENTIAL CARRIER ASSEMBLY |
![]() |
Set the differential carrier to an overhaul stand, etc. as shown in the illustration.
| 4. INSPECT RUNOUT OF DIFFERENTIAL RING GEAR |
![]() |
Using a dial indicator, check the runout of the differential ring gear.
| 5. INSPECT DIFFERENTIAL RING GEAR BACKLASH |
![]() |
Using a dial indicator, check the backlash of the differential ring gear.
| 6. INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION |
![]() |
Coat 3 or 4 teeth at 3 different positions on the differential ring gear with Prussian blue.
Hold the rear drive pinion companion flange sub-assembly firmly and rotate the differential ring gear in both directions.
Inspect the tooth contact pattern.

| Thickness mm (in.) | Thickness mm (in.) | Thickness mm (in.) |
| 2.26 to 2.28 (0.0890 to 0.0898) | 2.41 to 2.43 (0.0949 to 0.0957) | 2.56 to 2.58 (0.1008 to 0.1016) |
| 2.29 to 2.31 (0.0902 to 0.0909) | 2.44 to 2.46 (0.0961 to 0.0969) | 2.59 to 2.61 (0.1020 to 0.1028) |
| 2.32 to 2.34 (0.0913 to 0.0921) | 2.47 to 2.49 (0.0972 to 0.0980) | 2.62 to 2.64 (0.1031 to 0.1039) |
| 2.35 to 2.37 (0.0925 to 0.0933) | 2.50 to 2.52 (0.0984 to 0.0992) | 2.65 to 2.67 (0.1043 to 0.1051) |
| 2.38 to 2.40 (0.0937 to 0.0945) | 2.53 to 2.55 (0.0996 to 0.1004) | 2.68 to 2.70 (0.1055 to 0.1063) |
| 7. INSPECT DIFFERENTIAL PINION AND SIDE GEAR BACKLASH |
![]() |
Using a dial indicator, check the backlash of the differential side gear while holding one of the pinion gears toward the differential case assembly.
| 8. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the runout of the rear drive pinion companion flange sub-assembly vertically and horizontally.
| 9. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD |
![]() |
Using a torque wrench, measure the preload of the differential drive pinion.
| Preload |
| 0.6 to 0.9 N*m (6.1 to 9.2 kgf*cm, 5.3 to 8.0 in.*lbf) |
| 10. INSPECT TOTAL PRELOAD |
![]() |
Using a torque wrench, measure the total preload.
| 11. REMOVE REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL |
![]() |
Using SST, remove the 2 rear differential side gear shaft oil seals from the rear differential carrier sub-assembly.
| 12. REMOVE REAR DRIVE PINION NUT |
![]() |
Using SST and a hammer, unstake the staked part of the rear drive pinion nut.
![]() |
Using SST to hold the rear drive pinion companion flange sub-assembly, remove the rear drive pinion nut.
| 13. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY |
![]() |
Using SST, remove the rear drive pinion companion flange sub-assembly.
| 14. REMOVE REAR DIFFERENTIAL DUST DEFLECTOR |
![]() |
Using SST and a press, remove the rear differential dust deflector.
| 15. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL |
![]() |
Using SST, remove the rear differential carrier oil seal from the rear differential carrier sub-assembly.
| 16. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER |
| 17. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING |
![]() |
Using SST, remove the rear drive pinion front tapered roller bearing from the differential drive pinion.
| 18. REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER |
| 19. REMOVE REAR DIFFERENTIAL CASE |
![]() |
Put matchmarks on the rear differential bearing cap and rear differential carrier sub-assembly.
Remove the 4 bolts and 2 rear differential bearing caps.
![]() |
Using SST and a hammer, remove the 2 rear differential side gear shaft plate washers.
![]() |
Remove the rear differential case and the 2 rear differential case bearing outer races from the differential carrier.
| 20. REMOVE DIFFERENTIAL DRIVE PINION |
Remove the differential drive pinion.
| 21. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING |
![]() |
Using SST and a press, remove the rear drive pinion rear tapered roller bearing from the differential drive pinion.
Remove the rear differential drive pinion plate washer.
| 22. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING |
![]() |
Using a brass bar and a hammer, remove the rear drive pinion front tapered roller bearing (outer race) from the rear differential carrier sub-assembly.
| 23. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING |
![]() |
Using a brass bar and a hammer, remove the rear drive pinion rear tapered roller bearing (outer race) from the rear differential carrier sub-assembly.
| 24. REMOVE DIFFERENTIAL RING GEAR |
![]() |
Put matchmarks on the differential ring gear and rear differential case.
Using a screwdriver and a hammer, unstake the 4 rear differential ring gear set bolt lock plates.
Remove the 8 bolts and 4 rear differential ring gear set bolt lock plates.
| 25. INSPECT RUNOUT OF REAR DIFFERENTIAL CASE |
![]() |
Install the rear differential case to the rear differential carrier sub-assembly.
Install the right and left rear differential bearing caps with the 4 bolts.
Using a dial indicator, measure the differential case runout.
Remove the rear differential case.
| 26. REMOVE REAR DIFFERENTIAL CASE BEARING (for LH Side) |
![]() |
Using SST, remove the rear differential case bearing from the rear differential case.
| 27. REMOVE REAR DIFFERENTIAL CASE BEARING (for RH Side) |
![]() |
Using SST, remove the rear differential case bearing (RH) from the rear differential case.
| 28. REMOVE REAR DIFFERENTIAL PINION SHAFT |
![]() |
Using a pin punch (5 mm) and a hammer, remove the rear differential pinion shaft straight pin.
![]() |
Remove the rear differential pinion shaft. (A)
Remove the 2 differential pinion gears. (B)
Remove the 2 rear differential pinion thrust washers. (C)
Remove the 2 differential side gears. (D)
Remove the 2 No. 1 rear differential side gear thrust washers. (E)
| 29. INSPECT DIFFERENTIAL PINION AND SIDE GEAR |
Check that there is no damage to the differential pinion gears and side gears. If the differential pinion gears and/or side gears are damaged, replace them with new ones.
| 30. INSPECT REAR DIFFERENTIAL CASE |
Check that there is no damage to the differential case. If the differential case is damaged, replace it.