Home › DRIVE LINE › DIFFERENTIAL › REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL > REMOVAL

for Preparation Click here



1. REMOVE REAR WHEEL


2. REMOVE REAR DIFFERENTIAL FILLER PLUG


    C166706
  1. Using a hexagon wrench (10 mm), remove the rear differential filler plug and rear differential filler plug gasket.



3. REMOVE REAR DIFFERENTIAL DRAIN PLUG


    C166707
  1. Using a hexagon wrench (10 mm), remove the rear differential drain plug and rear differential drain plug gasket, and drain the oil.



4. SEPARATE REAR SPEED SENSOR


    C165809
  1. Remove the bolt and separate the rear speed sensor from the rear axle carrier sub-assembly.

    NOTICE:
    Keep the sensor tip and rear speed sensor installation hole free from foreign matter.



5. REMOVE REAR AXLE SHAFT NUT


    C165539E01
  1. Using SST and a hammer, release the staked part of the rear axle shaft nut.

    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the threads of the drive shaft may be damaged.

  1. While applying the brakes, remove the rear axle shaft nut.



6. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY


    C165996
  1. Remove the 2 bolts and separate the rear disc brake caliper assembly.

    NOTICE:
    Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.



7. REMOVE REAR DISC


    C166438E01
  1. Put matchmarks on the rear disc and the axle hub.



    D028126
  1. Release the parking brake and remove the rear disc.

    HINT:
    If the disc cannot be removed easily, turn and press firmly the shoe adjuster until the wheel comes free.



8. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY


    C166348E01
  1. Put matchmarks on the drive shaft and axle hub.

    NOTICE:
    Do not punch the marks.



    C165997
  1. Remove the 4 bolts and the rear axle hub and bearing assembly.

    NOTICE:
    1. Do not rotate the drive shaft with the rear axle hub and bearing assembly removed.
    2. Use wire or an equivalent tool to keep the parking brake assembly from hanging down by the parking brake cable assembly.



9. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY


    C165998
  1. Remove the bolt and the nut, and separate the No. 3 parking brake cable assembly.



10. REMOVE REAR STRUT ROD ASSEMBLY


    C165999
  1. Remove the 2 bolts, the 2 nuts, and the rear strut rod assembly.

    NOTICE:
    Since stopper nuts are used, loosen the bolts.



11. REMOVE REAR AXLE CARRIER SUB-ASSEMBLY


    C166000
  1. Loosen the 2 bolts.

    NOTICE:
    Since stopper nuts are used, loosen the bolts.



    C166001
  1. Remove the 2 bolts and 2 nuts, and separate the rear shock absorber with coil spring (lower side) from the rear axle carrier sub-assembly.

    NOTICE:
    1. Be careful not to damage the outboard joint boot.
    2. Be careful not to damage the speed sensor rotor.



    C166002
  1. Remove the 2 bolts, the 2 nuts, and the rear axle carrier sub-assembly.

    NOTICE:
    1. Be careful not to damage the outboard joint boot.
    2. Be careful not to damage the speed sensor rotor.

    HINT:
    Use wire or an equivalent tool to keep the rear drive shaft assembly from hanging down.



12. REMOVE NO. 2 REAR SUSPENSION ARM ASSEMBLY


C166222E01
  1. Put matchmarks on the adjust cams and the rear suspension member sub-assembly.

  1. Remove the nut, the No. 2 camber adjust cam, the rear suspension toe adjust cam sub-assembly, and the rear No. 2 suspension arm assembly LH.

    NOTICE:
    Mark the removed parts to distinguish left from right and keep them in order for reinstallation.

    HINT:
    When removing the nut, keep the rear suspension toe adjust cam sub-assembly from rotating.



13. REMOVE NO. 1 REAR SUSPENSION ARM ASSEMBLY


C166220
  1. Remove the bolt, the nut, and the rear No. 1 suspension arm assembly LH from the rear suspension member sub-assembly.

    NOTICE:
    Since a stopper nut is used, loosen the bolt.



14. REMOVE REAR DRIVE SHAFT ASSEMBLY


    C165540E01
  1. Using SST, remove the rear drive shaft assembly as shown in the illustration.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    Remove the rear drive shaft assembly while keeping it level.



15. REMOVE REAR DRIVE SHAFT SNAP RING


    C057543E04
  1. Using a screwdriver, remove the rear drive shaft snap ring.



16. REMOVE REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


    C168602E01
  1. Using SST, remove the rear differential side gear shaft oil seal.

    SST
    09308-00010